17 August 2022 in Computers & Geosciences
22 November 2022 in Geophysical Journal International
SUMMARY: Seismic inversion of amplitude versus offset (AVO) data in viscoelastic media can potentially provide high-resolution subsurface models of seismic velocities and attenuation from offset/angle seismic gathers. P- and S-wave quality factors (Q), whose inverse represent a measure of attenuation, depend on reservoir rock and pore fluid properties, in particular, saturation, permeability, porosity, fluid viscosity and lithology; however, these quality factors are rarely taken into account in seismic AVO inversion. For this reason, in this work, we aim to integrate quality factors derived from physically based models in AVO inversion by proposing a gradient descent optimization-based inversion technique to predict the unknown model properties (P- and S-wave velocities, the related quality factors and density). The proposed inversion minimizes the non-linear least-squares misfit with the observed data. The optimal solution is iteratively obtained by optimizing the data misfit using a second-order limited-memory quasi-Newton technique. The forward model is performed in the frequency–frequency-angle domain based on a convolution of broad-band signals and a linearized viscoelastic frequency-dependent AVO (FAVO) equation. The optimization includes the adjoint-state-based gradients with the Lagrangian formulation to improve the efficiency of the non-linear seismic FAVO inversion process. The inversion is tested on synthetic seismic data, in 1-D and 2-D, with and without noise. The sensitivity for seismic quality factors is evaluated using various rock physics models for seismic attenuation and quality factors. The results demonstrate that the proposed inversion method reliably retrieves the unknown elastic and an-elastic properties with good convergence and accuracy. The stability of the inverse solution especially seismic quality factors estimation relies on the noise level of the seismic data. We further investigate the uncertainty of the solution as a function of the variability of the initial models.
1 March 2016 in Geophysics
In reverse time migration (RTM) or full-waveform inversion (FWI), forward and reverse time propagating wavefields are crosscorrelated in time to form either the image condition in RTM or the misfit gradient in FWI. The crosscorrelation condition requires both fields to be available at the same time instants. For large-scale 3D problems, it is not possible, in practice, to store snapshots of the wavefields during forward modeling due to extreme storage requirements. We have developed an approximate wavefield reconstruction method that uses particle velocity field recordings on the boundaries to reconstruct the forward wavefields during the computation of the reverse time wavefields. The method is computationally effective and requires less storage than similar methods. We have compared the reconstruction method to a boundary reconstruction method that uses particle velocity and stress fields at the boundaries and to the optimal checkpointing method. We have tested the methods on a 2D vertical transversely isotropic model and a large-scale 3D elastic FWI problem. Our results revealed that there are small differences in the results for the three methods.
1 January 2016 in Geophysics
Subbasalt imaging has gained significant interest in the last two decades, driven by the urge to better understand the geologic structures beneath volcanic layers, which can be up to several kilometers thick. This understanding is crucial for the development and risking of hydrocarbon play models in these areas. However, imaging based on the reflection seismic data alone suffers from severe amplitude transmission losses and interbed multiples in the volcanic sequence, as well as from poor definition of the subbasalt velocity structure. We have considered a sequential imaging workflow, in which the resistivity model from joint controlled-source electromagnetic and magnetotelluric data inversion was used to update the velocity model and to improve the structural definition in the migrated seismic image. The quantitative link between resistivity and velocity was derived from well data. The workflow used standard procedures for seismic velocity analysis, electromagnetic data inversion, and well analysis, and thereby allowed detail control and input based on additional geophysical knowledge and experience in each domain. Using real data sets from the Faroe-Shetland Basin, we can demonstrate that the integration of seismic and electromagnetic data significantly improved the imaging of geologic structures covered by up to several-kilometer-thick extended volcanic sequences. The improved results might alter the interpretation compared with the imaging results from seismic data alone.
24 March 2026 in Mathematical Geosciences
Seismic inversion contributes significantly to the estimation of subsurface properties based on seismic reflection data, serving as an essential step in reservoir modeling. Unlike conventional post-stack acoustic impedance inversion, this study presents a model-based nonlinear pre-stack inversion approach to estimate acoustic impedance, shear impedance, and density models, which are crucial for mapping subsurface lithofluid properties. The inversion algorithm comprises a convolutional model using a linearized amplitude versus offset approximation, the sum of squares of data misfit between theoretical model predictions and actual observations, and a Hessian-free conjugate gradient method and a nonlinear limited-memory quasi-Newton algorithm, which approximates second-order Hessian behavior, are employed to iteratively minimize the data misfit by fitting trial models to observed data. As the key novelty of this work, analytical adjoint-state gradients for acoustic (P-wave) and shear (S-wave) impedances are explicitly derived, which can eliminate the computational burden of finite-difference gradient approximations typically used in seismic inversion, while significantly improving the efficiency and scalability of large-scale seismic inversions. Meanwhile, Tikhonov and total variation regularization constraints are also applied to generate smooth estimated models for the ill-conditioned inverse problem. The proposed inversion technique is evaluated using a synthetic example based on one-dimensional well logs, a two-dimensional Marmousi model, and Troll field data from the Norwegian North Sea. Our investigations indicate that the estimated impedances and density models are accurate and stable, and the method provides good convergence to an optimal solution to the nonlinear inverse problem. A comparison of the sensitivity of the inversion results to the initial models is performed using Monte Carlo simulation and continuous ranked probability scores.