1 December 2022 in Journal of Hydraulic Engineering
A physical model study was conducted on jet impingement in a plunging dropshaft with different drop heights of 3.38 and 1.88 m. Experimental observations show that an upward splash, annular flow, and downward bounced jet could be formed when the approaching jet hits the opposite shaft wall. The impinging pressure on the shaft wall was mainly dominated by the incoming flow velocity, and the mean pressure on the shaft wall can be reasonably well-predicted when considering the bounced flow. The pulsation of the impinging pressure on the shaft wall was significant, with the maximum pressure being approximately 1.4–3.8 times the mean value. The impinging pressure at the shaft bottom was primarily determined by the velocity at which the falling jet reached the pool. The mean value can be well estimated using the annular flow and bounced jet assumption. The pulsation intensity increased with an increase in drop height or flow rate, which could be alleviated by a plunging pool with a larger depth. However, for flows in dropshafts under study, the impinging pressure and the hydrostatic pressure of the cushion layer were within the same order of magnitude; thus, the increase of the pool depth leads to a reduction of the energy-dissipation rate.
11 January 2022 in Journal of Hydraulic Research
In urban stormwater systems, a rapid increase in water inflow can cause the entrapment of air pockets and subsequent ejection of air/water mixture, commonly known as storm geysers. In this study, a three-dimensional computational fluid dynamics model was built based on a lab model, which consisted of an upstream pipe and a downstream pipe with different invert elevation (i.e. a drop), connected by a chamber with a riser on the top. The effects of the downstream pipe characteristics, location of the entrapped air pocket, and its volume on the pressure variation were examined. With the downstream pipe flowing in full, two mechanisms that possibly trigger geyser events were simulated and experimentally validated: (1) a rapid inflow front in the upstream pipe with the flow changing from free surface flow to pressurized flow, and (2) the air pocket releasing in a pressurized system. For the first mechanism, the pressure surge in the chamber was related to the capacity of the downstream pipe for the increased flow rate. For the second mechanism, a smaller air pocket in the upstream pipe can generate a higher pressure during the geyser event due to the reduced damping effect on the pressure variation. A larger pressure drop was observed for a larger volume of released air. Lower peak pressure was generated for an air pocket closer to the chamber due to the shorter duration for pressure to build up before the air pocket reached the chamber.
17 January 2024 in Water Science & Technology
As an important component of the deep tunnel drainage system for dealing with urban waterlogging, the rotating stepped dropshaft has been proposed due to its small air entrainment. However, the hydraulic characteristics inside the shaft still need to be fully studied. In this study, the flow patterns, water velocity, and pressure in the rotating stepped dropshaft under different flow rates and geometric parameters were studied using a three-dimensional numerical model. The results show that increasing the central angle of the step and reducing the step height can both reduce the terminal velocity. A theoretical formula for predicting the terminal velocity was established and well validated. The connection between the shaft and the outlet pipe poses a severe threat to the structural safety due to alternating positive and negative pressures. Wall-attached swirling flow generates a circular high-pressure zone at the bottom of the dropshaft and the larger the flow rate, the greater the pressure gradient at the center of the bottom. By using the momentum theorem and considering the impact pressure range of the swirling flow, the shaft bottom pressure can be predicted reasonably well.
10 November 2023 in Journal of Pressure Vessel Technology
Long-distance water supply systems are important measures to improve the water resources distribution, and the water hammer protection devices such as air vessels are usually added in the project to ensure the safety and stable operation. However, the sediment particles are always ignored in the design. Hence, a numerical model and program were established for sediment laden water hammer based on the method of characteristics (MOC). Using the proposed model, the water hammer protection influences of sediment particles parameters are simulated for the same pipeline system of a water supply project. The result shows that the resistance loss of sediment-laden water in pipelines is larger than that of water, and the initial head of pump needed to be increased to ensure the water levels of downstream reservoirs are consistent. After power failure and pump stopping, the negative pressure wave of sediment-laden water is 2.97 m higher than that of water, and the theoretical minimum internal pressure along pipelines is 7.8 m lower. With the same air vessel protection, the lowest minimum internal pressure heads along pipelines decrease with the increase of quantities of sediment, while the results show no obvious influence by changes of median particle diameters. The lowest absolute pressure of pipeline could reach −0.69 m under the condition of 50 kg/m3 quantity of sediment and 0.05 mm median particle diameter. The relevant research results are of great significance sediment-laden water hammer numerical simulation and water hammer protection design.
1 April 2025 in Physics of Fluids
Falling water in dropshafts can induce a significant amount of airflow into sewer systems. In this study, the air demand in plunging-type dropshafts with medium drops of 3.38 and 1.88 m were investigated. The downward movement of air in the dropshaft is influenced by two components of falling water: the annular flow attached to the shaft wall and the bounced flow (in the forms of mainstream or water droplets). A model for predicting air pressure gradients was developed and experimentally validated. The air demand increased with the air inlet area, the drop height, the water flow rate, and the ratio of the bounced jet to the total water flow rate. A prediction model for the air demand in dropshafts was developed, thus it is possible to assess the air demand of dropshafts across a range of drop heights, diameters, and inflow conditions. When the air inlet to the shaft is restricted, a large negative pressure is generated inside the shaft, increasing the height of the water-air mixture generated by the bottom jet impact, which reduces the impact pressure at the bottom.
1 August 2024 in Physics of Fluids
The large aspect ratio of a corridor-shaped air cushion surge chamber in hydropower systems results in special hydraulic and heat transfer characteristics that differ from those of cylindrical shapes. The complexities of inflow jet and outflow vortex phenomena at the throttle orifice, along with the thermal energy exchange across the water–air interface during load variations, continue to be areas of limited understanding. The hydraulic and heat transfer processes during the load variation conditions were simulated precisely using the volume of fluid model to address the above knowledge gap by adopting computational fluid dynamics. The effects of various parameters on pressure and flow patterns (including initial water depth, orifice size, aspect ratio of the surge chamber, and unit closure time) and the thermodynamic response of the air during the compression and expansion phases were analyzed. The results indicate that a smaller orifice size has larger Froude numbers, thus intensifying jet heights and exacerbating wave fluctuations. An increased initial water depth or a reduced aspect ratio of the corridor-shaped chamber decreases the angular velocity of the fluid above the orifice during load increase, thus attenuating the vortex intensity. A method for calculating the heat transfer rate in the chamber was developed by considering the heat exchanges between water, chamber wall, and air. The intense heat transfer at the water–air interface is caused by large wave fluctuations due to velocity gradients. In addition, larger orifice size increases the flow rate and heat transfer rate, leading to an increase in the total heat transfer coefficient of the chamber.