EEPIS Robotics Research Center (ER2C) Electronics Engineering Polytechnic Institute of Surabaya (EEPIS) St. Raya ITS, Keputih, Sukolilo, Surabaya, Indonesia, 60111
Auto-generated profile, based on publicly available information
Eko Henfri Binugroho
EEPIS Robotics Research Center (ER2C) Electronics Engineering Polytechnic Institute of Surabaya (EEPIS) St. Raya ITS, Keputih, Sukolilo, Surabaya, Indonesia, 60111
Balancing robot which is proposed in this paper is a robot that relies on two wheels in the process of movement. Unlike the other mobile robot which is mechanically stable in its standing position, balancing robot need a balancing control which requires an angle value to be used as tilt feedback. The balancing control will control the robot, so it can maintain its standing position. Beside the balancing control itself, the movement of balancing robot needs its own control in order to control the movement while keeping the robot balanced. Both controllers will be combined since will both of them control the same wheel as the actuator. In this paper we proposed a cascaded PID control algorithm to combine the balancing and movement or distance controller. The movement of the robot is controlled using a distance controller that use rotary encoder sensor to measure its traveled distance. The experiment shows that the robot is able to climb up on 30 degree sloping board. By cascading the distance control to the balancing control, the robot is able to move forward, turning, and reach the desired position by calculating the body's tilt angle.
Unicycle mobile robot is wheeled mobile robot that can stand and move around using one wheel. It has attached a lot of researchers to conduct studies about the system, particularly in the design of the system mechanisms and the control strategies. Unlike two wheel balancing mobile robot which mechanically stable on one side, unicycle mobile robot requires additional mechanisms to keep balancing robot on all sides. By assuming that both roll dynamics and pitch dynamics are decoupled, so the balancing mechanisms can be designed separately. The reaction wheel is used for obtaining balancing on the roll angle by rotating the disc to generate momentum. While the wheeled robot is used for obtaining balancing on the pitch angle by rotating wheel to move forward or backward. A PID controller is used as balancing control which will control the rotation motor on the reaction disc and wheel based on the pitch and roll feedback from the sensor. By adding the speed controller to the pitch control, the system will compensate automatically for perfectly center of gravity on the robot. Finally, the unicycle robot will be able to balance on pitch angle and roll angle. Based on simulation result validates that robot can balance using PID controller, while based on balancing pitch experiment result, robot can achieve balancing with maximum inclination about ±23 degree on pitch angle and ±3.5 degree on roll angle with steady state error 0.1 degree.
Basically Biped robots had to walk like human, to generate this system we use basic approach for analysis human walking behavior. Human walking behavior can be analyzed using Zero Moment Point (ZMP). Zero Moment Point (ZMP) is a zero point which total of gravity forces and horizontal inertia equal 0 (Zero). This paper describes about early step to made basic walking trajectory for FLoW robot. To determine the best Zero Moment Point (ZMP) reference, it can use the comparison of distance and time. From this comparison, the walking characteristic of FLoW robot was found and the best Zero Moment Point (ZMP) trajectory also founded. The basic walking trajectory will generate based on the best Zero Moment Point (ZMP) trajectory as a reference. In the FLoW robot, the best Zero Moment Point Trajectory was founded at distance of 14cm with difference of Zero Moment Point Reference and Real Zero Moment Point equal 0.012cm.
Pens-Wheel is an electric vehicle which uses one wheel that able to balance itself so the rider does not fall forward or backward while riding it. This vehicle uses one brushless DC motor as actuator which capable to rotate in both directions symmetrically. The vehicle uses a combination of accelerometer and gyroscope contained in IMU (Inertial Measurement Unit) for balancing sensor. The controlled motion on the vehicle occurs only on the x-axis (pitch angle), in forward and backward directions. The PID (Proportional Integral Derivative) control algorithm is used to maintain the balance and movement of the vehicle. From the simulation and application in the real vehicle, the use of PID control is capable driving the vehicle in maintaining the balance condition within ±10° tilt angle boundary on flat surface, bumpy road, and inclining road up to 15° slope.
Zero moment point (ZMP) is a mathematical formulation to find a point that causes equilibrium of action and reaction momentum (momentum equal to zero). ZMP can be approached using Single Linear Inverted Pendulum Model (SLIPM). In this paper will explain the modeling of walking trajectory based on the mathematical formulation in SLIPM on the “T-FLoW” humanoid robot. In the SLIPM mathematical equation has 2 main components which are position vector of Center of Mass (CoM) and Acceleration (Linear) of CoM. From these two main compositions, there will be two types of walking trajectory models to be used and implemented in the “T-FLoW” humanoid robot. The first walking locomotion analysis is walking trajectory model the position vector of CoM is dominant. The second walking locomotion analysis is walking trajectory model when the acceleration in CoM is dominant. The results of these two walking trajectory models are for modeling and establishing a control system for robot stability based on dynamic characteristic on both walking trajectory models in the next research.