27 March 2026 in IEEE Transactions on Instrumentation and Measurement
The strain measurement accuracy of aerospace hot end components is severely affected by the change of environmental temperature. How to reduce the apparent strain derived from temperature variation within a wide range still is of a great challenge hitherto. In this work, a self-compensated thin film strain gauge (SC-TFSG) with sensing resistor and suspended compensation resistor is developed. These two resistors are orthogonal to each other and form a half bridge measurement structure, which is used to reduce the apparent strain introduced by temperature changes. Results show that the temperature coefficient of resistance (TCR) of the SC-TFSG is only -136 ppm/°C within a wide temperature range from room temperature to 1200 °C. The thermal output is 89.52% lower than the strain gauges without compensation resistor. Furthermore, the results of the standard strain cyclic loading test at 600 °C, 800 °C, 1000 °C and 1200 °C indicate that the maximum error between the SC-TFSG measured values and the standard loading strain can be controlled within 6%. The work provides an effective method for strain measurement and accuracy compensation of hot end components in a wide temperature range.
4 August 2025 in IEEE Sensors Journal
Piezoresistive sensor arrays enable intensive multiparameter signal acquisition for regional measurements. However, these arrays pose a significant challenge for obtaining precise measurement results due to crosstalk from the resistors of adjacent rows and columns. Various acquisition circuits have been proposed to suppress crosstalk, with the most common being the voltage feedback method (VFM) and the zero potential method (ZPM). These methods typically rely on multipole double-throw (MPDT) switches as chip-selection components. A major drawback of such designs is the large number of control ports required, which limits the scalability of the sensor array. Herein, a new VFM-based solution to ameliorate the measurement circuit is proposed. Through replacing MPDT switches with analog multiplexers, establishing row feedback using voltage-difference resistors, and obviating column feedback by diversion method, the number of control ports for a $32\times 32$ array comprising 1024 sensors was reduced from 64 to 10. Furthermore, a measurement errors of less than 0.07% can be achieved in simulation tests by using this newly designed circuit and approximately 0.5% in actual tests.
3 June 2025 in IEEE Sensors Journal
Wire retention force is an important indicator for evaluating the reliability of wire insertion in electrical connectors. Current approaches to measure this force are mainly relied on spring-based dynamometers, which are limited by their large sizes and lack of digital testing capabilities. Herein, this paper proposes a retention force sensor by controlling the critical friction force between the wires and textured rubber friction pair installed on fingertip. A conversion model between the normal pressure applied to the friction pair and the wire retention force was established, by combining experimental calibration and machine learning methods. Results show that the relative testing error of retention force using this fingertip sensor is less than 8%, and the coefficient of determination R2 of the sensor is better than 0.908 within the retention force range of 2~16N. After 1000 cycles of retention force testing, the testing error of sensor can still be maintained within 10%, indicating that the sensor has good long-term performance stability.
1 October 2026 in IEEE Sensors Journal
1 January 2026 in IEEE Transactions on Industrial Electronics
8 December 2025 in IEEE Sensors Journal
Diffusion is a critical doping process in silicon-based strain gauge fabrication, significantly influencing device performance. Traditional tube diffusion relies on empirical methods and repeated trials, limiting cost reduction and making it difficult to determine process parameters from strain gauge design requirements. Moreover, the cross effects between diffusion parameters are not fully understood. This paper develops a predictive model for tube diffusion using a solid-state boron nitride (BN) source, based on the response surface method (RSM). The model allows rapid determination of diffusion temperature, time, and protective argon flow rate to achieve target sheet resistance. Response surface analysis reveals that increasing temperature and time lowers sheet resistance and enhances uniformity, while time and flow rate show negligible cross effects. Multi-physical field simulations analyze the cross effects between temperature and flow rate, indicating that flow rates above 550 sccm increase temperature differences across wafers, reducing diffusion flux and uniformity. Experimental validation demonstrates a mean error of only 2.9% between predicted and actual sheet resistance, confirming the model’s accuracy. Using the optimized diffusion parameters, a semiconductor strain gauge with a gauge factor (GF) of 69.62 and a temperature coefficient of gauge factor (TCGF) of 0.53% F.S./°C was successfully fabricated. This predictive approach provides an efficient strategy for optimizing diffusion processes in strain gauge manufacturing, offering both performance control and cost reduction.