18 September 2009 in Proceedings of the IEEE
As complementary metal-oxide-semiconductor (CMOS) technologies are scaled down into the nanometer range, a number of major nonidealities must be addressed and overcome to achieve a successful analog and physical circuit design. The nature of these nonidealities has been well reported in the technical literature. They include hot carrier injection and time-dependent dielectric breakdown effects limiting supply voltage, stress and lithographic effects limiting matching accuracy, electromigration effects limiting conductor lifetime, leakage and mobility effects limiting device performance, and chip power dissipation limits driving individual circuits to be more energy-efficient. The lack of analog design and simulation tools available to address these problems has become the focus of a significant effort with the electronic design automation industry. Postlayout simulation tools are not useful during the design phase, while technology computer-aided design physical simulation tools are slow and not in common use by analog circuit designers. In the nanoscale era of analog CMOS design, an understanding of the physical factors affecting circuit reliability and performance, as well as methods of mitigating or overcoming them, is becoming increasingly important. The first part of the paper presents factors affecting device matching, including those relating to single devices as well as local and long-distance matching effects. Several reliability effects are discussed, including physical design limitations projected for future downscaling. In some cases, it may be helpful to exceed foundry-specified drain-source voltage limits by a few hundred millivolts. Models are presented for achieving this, which include the dependence on the shape of the output waveform. The condition Vsb > 0 is required for cascode circuit configurations. The role of other terminal voltages is discussed, as Vsb > 0 increases both hot and cold carrier damage effects in highly scaled devices. The second part of the paper focuses on trends in device characteristics and how they influence the design of nanoscale analog CMOS circuits. A number of circuit design techniques employed to address the major nonidealities of nanoscale CMOS technologies are discussed. Examples include techniques for establishing on-chip accurate and temperature-insensitive bias currents, digital calibration of analog circuits, and the design of regulator and high-voltage circuits. Achieving high energy efficiency in ICs capable of accommodating 109 devices is becoming critically important. This paper also presents a survey of the evolution of figure of merit for analog-to-digital converters.
24 April 2017 in IEEE Journal of Solid-State Circuits
This paper presents a low-power 9-bit compiled successive-approximation register (SAR) analog-to-digital converter (ADC) for Bluetooth low energy receivers. The ADC is compiled from a SPICE netlist, a technology rule file, and an object definition file into a design rule check and layout versus schematic clean layout and schematic in 28-nm FDSOI. The compiled SAR ADC reduces the design time necessary to port to a new technology, and to demonstrate technology porting the same SAR ADC architecture is compiled in 28-nm FDSOI with Input/Output (IO) transistors. This paper also includes a comparator clock generation loop that uses the bottom plate of the capacitive digital-to-analog converter. The proposed compiled core transistor SAR ADC achieves the state-of-the-art Figure of Merit (FoM) of 2.7 fJ/conv.step at 2 MS/s, and 3.5 fJ/conv.step at 20 MS/s with an area of 0.00312 mm 2 .
19 December 2010 in Analog Integrated Circuits and Signal Processing
We present a differential comparator-based switched-capacitor (CBSC) pipelined analog-to-digital converter (ADC) with comparator preset, and comparator delay compensation. Compensating for the comparator delay by digitally adjusting the comparator threshold improves the ADC resolution from 2.5-bit to 7.05-bit. The ADC is manufactured in a 90 nm CMOS technology, with a core area of 0.85 mm × 0.35 mm, a 1.2 V supply for the core and 1.8 V for the input switches. It has an effective number of bits (ENOB) of 7.05-bit, and a power dissipation of 8.5 mW at 60 MS/s.
17 October 2023 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
This article presents analytical tools for high-level design of the leapfrog (LF) control-bounded analog-to-digital converter (CBADC). We derive closed-form design equations for parameterizing the analog system for a target signal-to-noise ratio (SNR) and bandwidth. Furthermore, we show how the parameterization can be modified to compensate for finite amplifier gain-bandwidth product (GBWP) and to control the signal swing at different nodes of the system. Behavioral circuit simulations are used to compare the LF CBADC to relevant continuous-time sigma–delta modulators (CT- $\Sigma \Delta $ Ms) in terms of nominal performance and sensitivity to component variations, clock jitter, and finite GBWP. Simulations show that the nominal performance of the LF is similar to that of a CT- $\Sigma \Delta \text{M}$ of the same loop-filter order and with the same number of quantization levels. The simple, modular structure, analytical stability guarantee, and single-bit quantizers make the LF an interesting alternative to conventional CT- $\Sigma \Delta $ Ms.