27 May 2021 in Archives of Civil and Mechanical Engineering
The article focuses on the Direct Drive Rotary Friction Welding of ultrafine-grained copper rods, which feature increased mechanical properties and good electrical properties, yet are limited in size. The use of UFG metals is often limited by the too small dimensions of semi-finished elements produced by SPD methods. Therefore, the production of finished machine parts from UFG metals is currently economically unjustified. Dismissal of dimensional limitations can be done by introducing joining to technological processes. The proposed joining method does not lead to a melting of the material in the joining zone or excessive degradation of the UFG microstructure. To obtain the best results, the research used the method of low-energy welding of two kinds of specimens: with a flat or a conical contact surface. In the article, the authors present, by means of metallographic microsections and microhardness measurements, the influence of rotational speed, welding pressure and conical shape contact surface on the quality of the obtained joints. The conducted research made it possible to obtain good quality joints whose microhardness is reduced only by about 10% in comparison with the base material and the tensile strength dropped from only 397–358 MPa.
1 May 2024 in Archives of Civil and Mechanical Engineering
When welding ultra-fine-grained metals using conventional methods, the microstructure in the joint area is degraded (mainly due to recrystallization) in the heat-affected zone and a significant deterioration of mechanical properties, including joint strength. The aim of the research presented in this article was to identify the possibility of obtaining joints with strength close to initial material using friction welding of metal materials with ultra-fine grain. For this purpose, UFG (ultra-fine-grained) material was produced from technically pure M1Ez4 copper using a hybrid SPD (severe plastic deformation) process. The welding process was carried out on a machine with a prototype design that allows minimizing the welding time, while generating high force. The process parameters used on the prototype machine resulted in an increase in the hardness of the material by 4% in the joint area. The strength of the joint compared to the base material decreased slightly by 2%. The tests carried out proved that, using appropriate process parameters, it is possible to obtain a UFG metal joint without a decrease in its mechanical strength.
1 January 2022 in Scientific Papers of Silesian University of Technology Organization and Management Series
Purpose: In the development of ideas for Industry 4.0, information about the element production cycle has become more and more important. Knowledge of the subsequent forming processes, determination of the machine on which the process has been carried out and of the type and wear of the tool, leads to smart production management, which plays an increasingly important role in the metal forming industry. To meet the current expectations for these challenges, an advanced technology needs to be introduced for monitoring the manufacturing processes by deploying flexible solutions. This technology must include, but not be limited to, identifying and tracking the product using laser marking. Design/methodology/approach: Laser marking allows a permanent mark in the form of a barcode to be applied to the sheet metal surface. Commonly used marking methods and the condition of the sheet metal surface can affect the marking contrast. This paper presents a concept for recording individual stages of sheet metal forming and determination of the impact of the laser marking technology on the contrast of the applied barcode. To ensure accurate control of the deformation stages, the bulging process of the spherical dome has been used as an example. Findings: Analysis of the influence of laser marking method on the barcode recognition accuracy can contribute to the development of smart management of the production process according to the idea of Industry 4.0. Research limitations/implications: A large plastic deformation has been applied to the sheet metal surface and no limitation in a barcode reading process (using vision scanning technology) was indicated. Also, the geometry deformation (different angle view of the CCD camera) of the barcode image has introduced no additional problems with a barcode reading. Originality/value: The optimal parameters of a laser marking technique for barcode marking, which are critical for the material that is subjected to metal forming operations that deform it, have been studied. The results shows that traceability is an attractive solution for tracking technological data in the production chain for a single-shaped product. Keywords: manufacturing control, laser marking, vision analysis, sheet metal forming, barcode quality. Category of the paper: Technical paper.
12 December 2019 in Archives of Metallurgy and Materials
Advanced vision method of analysis of the Erichsen cupping test based on laser speckle is presented in this work. This method proved to be useful for expanding the range of information on material formability for two commonly used grades of steel sheets: DC04 and DC01. The authors present a complex methodology and experimental procedure that allows not only to determine the standard Erichsen index but also to follow the material deformation stages immediately preceding the occurrence of the crack. Accurate determination of these characteristics in the sheet metal forming would be an important application, especially for automotive industry. However, the sheet metal forming is a very complex manufacturing process and its success depends on many factors. Therefore, attention is focused in this study on better understanding of the Erichsen index in combination with the material deformation history.
16 December 2024 in Archives of Metallurgy and Materials
Joining metals with ultra-fine grains (UFG) is very difficult. UFG metals have a grain size of less than 1 µm. Exceeding the recrystallization temperature causes the growth of ultra-fine grains and degradation of the material’s mechanical properties. The process temperature is influenced by the amount of energy supplied to the joint, which depends on the power and time. Conventional machines are not adapted to effectively conduct the process in extremely short friction times. For this reason, this article presents the welding process on the W2Mi prototype machine. The design of this machine allows the joining of UFG metals in less than 100 ms. UFG material produced using the hybrid SPD (Severe Plastic Deformation) process from technically pure CW004A(Cu-ETP) copper was used for welding tests. The joint obtained on the W2Mi machine did not show any significant degradation signs of mechanical properties. At the same time, an increase in microhardness in the joint area by approximately 4% was noticed. The obtained results prove that the process of joining UFG metals was successfully carried out.
25 June 2025 in Archives of Metallurgy and Materials
Correct production of aluminium profiles requires optimising many parameters on the production line. Irregularities in the process cause, among others, unfavourable changes in the surface geometry structure (SGP) of the profile, including roughness. Therefore, assessing surface roughness makes it possible to identify abnormalities in the production process. An original vision system was proposed to analyse changes in the profile surface roughness during the extrusion process. The constructed system, placed on the production line, consists of a monochromatic camera and prototype illumination that enable recording profiles of various shapes. The system allows for quick detection of changes in the quality of the profile surface based on the analysis of reflected light distribution. The work presents, among others, a comparison of vision measurement results obtained during extrusion with the process parameters recorded on the production line.