16 June 2020 in IEEE Transactions on Antennas and Propagation
This paper presents a basic 3-D frequency selective surface (FSS) unit cell and its application for synthesis of highorder bandpass filtering response. The proposed FSS unit cell is constructed by stacked slotlines loading with shunted capacitive and/or inductive strip lines, which can be easily fabricated with traditional printed circuit board techniques. First, by analyzing the propagation characteristics of the stacked slotline, it can be found that the stacked slotline is seen as a transmission-line transformer, which can convert spatial electromagnetic waves into guided waves. Then, by loading shunted capacitive and/or inductive strip lines, equivalent capacitors and/or inductors are formed with the slotline section, which can be used to realize desirable resonators for bandpass filtering response. Equivalent circuit models are established and circuit parameters are extracted. With the aids of the generalized filter synthesis theory, the proposed unit cell is first applied to synthesize bandpass FSS with 1/4-wavelength transmission-line inverters. An example of a second-order Chebyshev bandpass FSS with the center frequency of 10 GHz is synthesized and designed. The measured results demonstrate that the desired bandpass filtering response is stable for oblique incidence. Furthermore, to obtain high-order response with a reduced FSS thickness, the proposed unit cell is then applied to synthesize bandpass FSS based on a lumped-element bandpass filter. The detailed synthesis procedure and derivations are given. Another example of a third-order Chebyshev bandpass FSS with the center frequency of 10 GHz is also designed, fabricated, and measured. The measured results show that the desired stable performance is realized and the total FSS thickness is 0.21λ0 (λ0 is the free-space wavelength at the center frequency).
11 January 2021 in IEEE Transactions on Antennas and Propagation
In this article, a low-profile and wideband circularly polarized patch antenna is proposed and developed, which is composed of the circular patch fed by four ports. A wideband property is achieved by utilizing TM 11 and TM 21 mode, as well as the orthogonal mode of TM 11 . The Γ-shaped feed is employed to stimulate the TM 21 mode. Besides, due to the parasitic radiation from the face-to-face Γ-shaped feeds with opposite phase, the radiation peak of the circular patch under TM 21 mode is along the broadside direction, which is different from the original radiation mechanism of TM 21 mode. By loading shorting pins in the middle area of circular patch, the polarization orthogonal mode of the fundamental mode (TM 11 ) is excited properly, which contributed to bandwidth enhancement. Cooperated with the quadrature phase feed network, a wideband circular patch antenna with unidirectional radiation and circular polarization properties is designed, fabricated, and measured. The size of the circular patch is 0.57λ 0 ×0.57 λ 0 and the height is only 0.053λ 0 ( λ 0 is the free space wavelength at the center frequency). The measured results show that the 109% of fractional bandwidth is obtained under the condition of VSWR <; 2, ranging from 0.94 to 3.18 GHz, and the 3 dB axial ratio fractional bandwidth is 95%, ranging from 1.04 to 2.93 GHz. Besides the realized LHCP gain >3 dBic from 1.27 to 2.99 GHz.
7 June 2022 in IEEE Transactions on Antennas and Propagation
This paper presents a synthesis method to design a new type of bandpass frequency selective surfaces (FSSs) with multiple transmission zeros (TZs). To briefly show the concept of our synthesis method, a generalized topology of the bandpass FSS based on cascaded slotline sections paralleled with bandpass resonators is first presented to map with an alternative nth-order bandpass filtering network with J-inverters and typical LC parallel resonators. Then, two kinds of composite LC parallel resonators, named as LC-LC and L-LC parallel resonators, are introduced and discussed to replace the typical LC parallel resonators, which can produce TZs at skirts of the passband and increase the out-of-band selectivity. The derivations of equivalent relationships between the composite and typical LC resonators are given. Further, for the exploration of bandpass FSS with multiple out-of-band TZs, the realization of these two discussed composite LC parallel resonators is exhibited by inductive and capacitive strip lines loading on slotline structures. The design curves and guidelines are given and discussed correspondingly. To validate our design concept, two FSS examples, a second-order bandpass FSS with four out-of-band TZs and a third-order one with five out-of-band TZs are synthesized and designed. In final, these two designed bandpass FSS prototypes are fabricated and then measured by the free-space measurement method. The measured results show that the desired stable bandpass filtering performance and independently multiple out-of-band TZs are successfully realized.
3 October 2022 in IEEE Transactions on Antennas and Propagation
In this article, an accurate and unified synthesis method for a class of 3-D bandpass frequency-selective structures (FSSs) is proposed. Each element of the presented 3-D FSSs is composed of stacked planar slotline sections cascaded with inductively-coupled structures. Herein, each inductively-coupled structure is modeled as an equivalent K -inverter, and each stacked slotline section is regarded as an equivalent transmission-line resonator. By defining three ideal calibration standards, i.e., short-circuit, open-circuit, and matched-load in a commercial electromagnetic full-wave simulator, a numerical short-open-load calibration technique is utilized to effectively extract all the equivalent circuit parameters involved in the presented 3-D FSS. Furthermore, a generalized synthesis design procedure is presented by mapping the proposed 3-D FSS topology onto a n th-order bandpass filtering network. To verify the feasibility of this design concept, two groups of design examples, including a single-polarized third-order Chebyshev bandpass FSS and two dual-polarized second-order ones, are respectively synthesized and designed. Finally, two prototypes of the designed 3-D FSS examples are fabricated, assembled, and then tested by using a free-space measurement method. The measured results exhibit good agreement with the predicted ones. The proposed 3-D FSSs feature simple topologies with high-order bandpass filtering responses and stable filtering responses under a large variation of incident angles of spatial waves.
14 February 2023 in IEEE Transactions on Antennas and Propagation
This article proposes a unified design method for a highly efficient wideband transmissive linear-to-circular polarization converter composed of two orthogonal adjacent-order bandpass filtering elements for the first time. First, the linear-to-circular polarization converter is constructed to convert two orthogonal linearly polarized (LP) spatial waves split from a 45°-slant incident plane wave into a desired circularly polarized (CP) wave. Taking advantage of the wideband filter synthesis method and phase shifter theory, polarization converter elements with prescribed specifications (e.g., fractional bandwidth, and Chebyshev passband ripple) are then synthesized by the corresponding low-characteristic-impedance bandpass filtering networks with the loading of shunt short-circuited stubs on quarter-wavelength transmission line sections. The adjacent-order phase difference function with a natural ± 90° value at center frequency can be simultaneously manipulated by filtering bandwidth. The theoretical axial ratio ( AR ) curve is calculated by the synthesized magnitude responses and phase deviation function. The design guideline is then summarized. Finally, based on the third- and fourth-order bandpass filtering networks, a prototype of the proposed linear-to-circular polarization converter operating at 5 GHz with a designable 70% 3-dB AR bandwidth is implemented, fabricated, and tested by the free-space measurement method. The transmitted CP wave with three in-band AR minima and relatively stable angular performances can be efficiently converted from the incident LP spatial wave as well verified in the experiment. The AR curves and design requirements of different adjacent-order bandpass filtering combinations are further explored according to the proposed design guideline.
2 August 2024 in IEEE Antennas and Wireless Propagation Letters
This letter presents a design methodology for single- and dual-band reflective-type 90° linear polarization rotators (PRs) utilizing orthogonally inserted coupling slotlines. Firstly, a reflective second-order PR element is designed by employing two meandered slotlines etched on orthogonal printed circuit boards (PCBs). An accurate equivalent circuit model (ECM) is utilized to analyze the proposed PR element. Secondly, by etching two additional slotlines in the same element, two coupling paths are established. By properly altering the coupling strength and the operation frequencies of the corresponding coupled slotlines, the single- and dual-band PRs can be realized, respectively. Meanwhile, the corresponding ECMs have been investigated to illustrate their operation principles. Finally, two prototypes have been fabricated and measured to verify the simulated results, and good agreements are achieved.