30 August 2023 in Transportation Research Record: Journal of the Transportation Research Board
The surface energy of aggregate in asphalt pavements has a huge impact on its moisture susceptibility. The commercial antistripping agents widely used in asphalt may not be effective enough to enhance the moisture resistance if large quantities of acidic aggregates exist in pavements. This is also the reason why moisture damage is still an issue in many U.S. regions primarily supplied with “problematic” aggregates. In this regard, a promising solution is to use waste-plastic-coated aggregate, the surface of which is fundamentally modified and has a high affinity with asphalt because of the hydrophobic nature of plastic. However, it has not been widely promoted in the industry since there needs to be a practical and reliable method for uniform coating and avoiding the agglomeration of fine aggregate. To this end, an entirely new coating technology (thermoplastic polyethylene powder coating [TPPC]) was developed to coat aggregate using polyethylene (PE) powder. This technology utilizes a cheap but highly wettable fluidized bed to stably disperse the hydrophobic PE powder. Then, the dispersion liquid is sprayed onto the hot aggregate where the fluidized bed will evaporate fast while the PE particles stay, melt, and coat the aggregate surface. The microstructures of the coated aggregate were directly observed by scanning electron microscopy. Surface energy-based thermodynamic parameters were used to demonstrate the effect of TPPC on the moisture resistance of asphalt mixtures. This technology can be extended to other types of waste plastic if suitable fluidized beds are developed.
14 December 2023 in Transportation Research Record: Journal of the Transportation Research Board
Modifying asphalt is a potentially high-value application for reusing waste plastics because of the high-volume usage of asphalt in highway construction. However, simply blending hot plastics and asphalt encounters difficulties related to the poor solubility of polymers, which limits the formation of a swollen network with asphalt molecules. The polymer phases also tend to coalesce and separate from asphalt during high-temperature storage in static conditions. The present study developed an innovative process to stabilize waste plastics in asphalt and improve binder storage stability by using lightly pyrolyzed crumb rubber together with a chemical compatibilizer. Both polymers were extruded to produce a thermoplastic elastomer (TPE) for asphalt modification. The mechanical performance and chemical reactions of TPEs were characterized via tension test and Fourier transform infrared spectroscopy. The storage stability and rheological properties of modified binder blends were evaluated through laboratory asphalt stability test and dynamic shear rheometer test. Polymer phases and network structures were characterized through optical microscopy. It was found that the pyrolyzed and reactive extrusion process improved the rubber solubility and polymer interaction, and therefore the storage stability of modified binder blends. The co-existence of rigid plastic and soft rubbery regimes in an entangled network provided a promising pathway to improve the mechanical performance of asphalt binders in both high- and low-temperature domains.
4 October 2025 in Transportation Research Record: Journal of the Transportation Research Board
Asphalt aging has been an important topic for decades, but in recent years many factors have further heightened emphasis on aging specifications. These factors may include but are not limited to the inertia to recycle, changing markets where more materials are placed near surfaces, mixes becoming more brittle and crack prone, and large price increases for virgin binders. The objective of this paper is to develop quantifiable relationships, for several binder properties, between hours of pressure aging vessel (PAV) conditioning and mixture field aging in a hot and non-freeze climate. Nine binders, 12 mixture variations, up to 10 years of field aging, and up to 160 PAV hours were included in the experimental matrix. Findings showed that the American Association of State Highway and Transportation Officials (AASHTO) R28 was able to simulate over 5 years of field aging with 20 PAV hours at 100°C when aging occurred at a depth of 5 to 6.3 cm from the pavement surface, but not when within 1.3 cm of the surface. The aging rate was roughly three times higher at the surface than at 5 to 6.3 cm deep. Air voids had over twice the impact on binder property changes at 5 to 6.3 cm deep than within 1.3 cm of the surface. R28 should consider modifying the significance and use portion of the standard to reflect that mixes within 1 to 2 cm of the surface are very unlikely to have 5 years of aging simulated by 20 PAV hours at 100°C.
26 June 2025 in Transportation Research Record: Journal of the Transportation Research Board
Although many states report successful use of tack coats to achieve adequate bonding between asphalt layers, not all states have experienced such success. Selecting an appropriate tack coat is crucial for overcoming poor bonding and ensuring optimal performance in the field. This study aimed to provide comprehensive guidance on selecting the right tack coat material, considering various construction methods and environmental conditions, to ensure effective bonding. Two asphalt mixture types (fine and coarse) and surface conditions (new asphalt concrete [AC], milled AC, and aged AC) were adopted in this study to determine the impact of existing pavement conditions on bonding performance. The effectiveness of various tack coat materials and their rheological properties was also assessed. The American Association of State Highway and Transportation Officials (AASHTO) TP114 (“Standard method for determining interlayer shear strength [ISS] of asphalt pavement layers”) was employed to evaluate the bonding performance of different tack coat materials, mixture types, and surface conditions. It was evident that using an improper tack coat could create a slip plane and reduce the interface shear strength, a problem not observed in samples without a tack coat. Additionally, a good correlation between tack coat rheological properties and ISS test results were observed.