23 October 2020 in Journal of Lightwave Technology
Co-packaged optics in next-generation datacenters require the assembly of multiple components on the same multichip module (MCM) and interconnection with hundreds of optical fibers. A novel photonic packaging substrate is required to leverage high-throughput electronic assembly with high precision optical alignment. This report highlights the results of glass substrate optimization to include optical waveguides, a fiber connector and chip interfaces, as well as features for electrical connectivity, as a potential component for a co-packaging solution. Glass with smooth surfaces and high precision alignment features enables surface mounted flip-chip assembly of electrical integrated circuits, photonic components, and optical fiber connectors. All components will be placed by vision alignment using precise fiducials or passive alignment in mechanical features to the surface of the glass substrate with optical and electrical interconnects. Flip-chip assembly of photonic components is enabled by evanescent coupling with couplers having a minimum non-linear taper length of 1.5 mm. The designed interface loss to the integrated ion-exchanged glass waveguides is less than 1 dB with an interface which is robust to lateral misalignment of up to 4 microns. Light can be transmitted in the glass substrate with a propagation loss of 0.1 dB/cm. Fiber interfaces are mechanically and thermally decoupled from the photonic component and glass waveguides can fan-out the component pitch from 50 microns to 250 microns of the MTP-16 ferrule connector. The solder reflow compatible connector receptacle is passively aligned and demonstrate with an average loss of 0.68 dB.
22 February 2023 in IEEE Journal of Selected Topics in Quantum Electronics
Placing the electrical and photonic chiplets in a single package leads to significant power reduction. Chiplets are connected by fine-line electrical routing over a length of a few millimeters and optical interconnects in the package connect photonic chips with optical fibers for off-package communication. A packaging substrate made of glass with optical waveguides, through glass vias and electrical redistribution layers inside a single-sided cavity enables lower-cost assembly. A single-sided 50 µm deep cavity was etched in glass, and electrical copper lines with 5 µm in height and width were deposited on the floor of the cavity. Ion-exchange (IOX) waveguides with propagation loss of <0.1 dB/cm were fabricated below the glass surface. For flip-chip assembly of photonic chips and optical coupling with the IOX waveguides at the top surface of the glass, all electrical interconnects were located inside the cavity. Photonic chips with silicon nitride waveguides were optically coupled to glass waveguides with a minimum loss of 0.5 dB, achieved by fiducial-aligned flip-chip photonic assembly. A low-profile fiber connector with height of 4.4 mm connects the integrated ion-exchanged waveguides with the optical fibers. Average connector loss of 0.83 dB was demonstrated with physical contact between fibers and IOX glass waveguides.
6 January 2025 in IEEE Transactions on Components, Packaging and Manufacturing Technology
Glass provides high dimensional stability and flatness, enabling high-throughput electronic assembly with high precision optical alignment for co-packaged optics (CPO) applications. Optical waveguides can be integrated in the glass core material by the thermal silver ion-exchange (IOX) process at temperatures around 350°C for fiber to chip connectivity. Currently available IOX glasses degrade due to ion mobility at operating conditions so we designed a new glass composition enabling waveguides to be stable over a lifetime of five years at an elevated temperature of 85°C or higher without performance degradation which could impact the integrity of the optical signal. The glass composition was optimized for thermal stability and low loss IOX waveguides were fabricated with propagation loss of only 0.034 dB/cm. Waveguide designs are studied and evaluated for waveguide crossings, high-density spacing, tight bends, high-optical power transmission, and polarization dependency. The waveguide technology is demonstrated for different applications including glass waveguide bridge for fiber to chip-coupling, multi-core fan-out, optical waveguide shuffle and an optical waveguide circuit for CPO with over 1024 waveguide interconnects.
9 February 2022 in Journal of Lightwave Technology
This paper reports on the demonstration of a single-mode flexible polymer optical interconnect for efficiently and conveniently connecting integrated photonics chips to one another (chip-to-chip) and to optical printed circuit boards (chip-to-board). The interconnect uses a low-loss partially fluorinated refractive index contrast (RIC) polymer, referred to as poly(F-SBOC), that provides for direct patterning of the desired refractive index profiles into a slab waveguide consisting of poly(F-SBOC) and a flexible fluoropolymer film (Tefzel). Using a maskless lithography system, interconnects consisting of s-bends and tapers can be printed in situ into the poly(F-SBOC) material with no need for mechanical alignment. We demonstrate the efficacy of this approach by connecting two separate ion-exchange (IOX) glass waveguide chips, achieving fiber-to-fiber total insertion losses below 6dB in some cases, through the use of grayscale tapers that are written directly into the poly(F-SBOC) material.
1 January 2022 in International Symposium on Microelectronics
Co-packaged optics leads to significant power reduction by placing the electronic and photonic chiplets in a single package. An integrated electro-optical substrate made of glass with optical waveguides, through vias and electrical redistribution layers inside a single-sided cavity enables fine-line electrical routing and low-cost assembly. Existing glass and thin film technologies were evaluated and combined into a single process stream including photonic assembly. Photonic chips with silicon nitride waveguides were optically coupled to integrated low-loss (<0.1 dB/cm) glass waveguides with minimum loss of 0.65 dB achieved by fiducial alignment and pick-and-place assembly.