Karaganda Technical University named after Abylkas Saginov, Faculty of Metallurgy and Mechanical Engineering, Department of Technological Equipment, Mechanical Engineering and Standardization, Karaganda, Kazakhstan
Auto-generated profile, based on publicly available information
I. A. Bartenev
Karaganda Technical University named after Abylkas Saginov, Faculty of Metallurgy and Mechanical Engineering, Department of Technological Equipment, Mechanical Engineering and Standardization, Karaganda, Kazakhstan
The article focuses on the results of a study of the effect of electroslag surfacing modes on the penetration depth of restored teeth, conducted on the basis of a full factorial experiment (FFE) type 22. The welding current and the voltage on the slag bath were selected as factors. Each experiment was repeated three times, and the results were analyzed to build a regression model that takes into account all interactions of factors. The article describes in detail the process of encoding variable factors, constructing a planning matrix, calculating the coefficients of the regression equation and checking them for significance using the Student’s criterion. The adequacy of the experiment was confirmed by calculations using the Fisher criterion (Fcalculated<Ftable). According to the results of the experiment, it was found that the stress on the slag bath has the most significant effect on the total depth of penetration. The optimal mode has been determined (welding current 400 A and voltage on the slag bath 45 V), which provides the required penetration depth (4.63 mm) of a large-modulus tooth. The convergence of the results of the full-scale test with the results of planning a full factor experiment of type 22 was revealed, which made it possible to determine the optimal surfacing mode. This study can be used to optimize the parameters of electroslag surfacing, which will lead to an increase in the quality and efficiency of restoration of worn teeth. Keywords: electroslag surfacing, surfacing mode, penetration depth, welding current, welded tooth.
30 September 2024 in Science and Technology of Kazakhstan
This study examines the quality of a gear tooth surface fragment restored through electric arc welding. Visual inspection revealed a defect-free, dense surface. Macrostructure examination displayed uniformity and absence of cracks in the metal sample. The high hardness (HRC-36.61) of the weld deposit is crucial for wear resistance, while the base metal, with lower hardness (HRC-29.09), ensures ductility and impact toughness. Martensitic and residual austenitic structures in the weld deposit indicate deformation-resistant properties, with austenite providing good ductility and martensite contributing to high hardness and strength, making the material resistant to wear and deformation under dynamic loads. Thin lens-like martensitic plates and a reed-like structure suggest unique formation characteristics during electroslag welding’s oxidizing-reducing reactions. Microstructure analysis revealed a finer structure in the weld deposit compared to the base metal. The base metal exhibited a ferrite-pearlite structure typical of many steels, unchanged after welding. The weld deposit showed elevated carbon (0.70 %) and manganese (1.38 %) concentrations, typical for weld deposits, influencing mechanical properties. Elements like manganese and molybdenum enhance wear resistance, while the presence of chromium (0.42 %) and nickel (0.12 %) improves corrosion resistance, crucial in aggressive environments. Keywords: large-module gears, tooth wear, electro slag surfacing, hardness, analysis
1 January 2025 in Journal of Applied Engineering Science
This study focuses on the restoration of large-module gear teeth of ball mills using the electroslag welding method, with an emphasis on practical results and mathematical modeling. The research established that optimal electroslag welding conditions are achieved by stabilizing key process parameters, such as current strength, slag bath voltage, and cooling water flow rate. For high-quality welding of gear teeth with a module of 20 mm, the following parameters are recommended: current strength I=362.5 A, slag bath voltage U=73.25-74 V, and water flow rate Qw=3-3.5 l/min. These parameters ensure minimal roughness and the required hardness of the welded teeth. Mathematical modeling provided equations linking welding modes with the roughness and hardness of the welded teeth. The presented experimental data are highly relevant for the scientific community and enterprises involved in the restoration of large-module gear wheels. The results hold significant practical value as they enable enterprises to reduce restoration costs and enhance the durability of components.