Baglan Smailova

Baglan Smailova


Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2024 in Material and Mechanical Engineering Technology
Verified
Journal Article
Closed access
TBToty Buzauova
Toty Buzauova
DSDalelehan Sarbaev
Dalelehan Sarbaev
BSBaglan Smailova
Baglan Smailova
STShamshygaiyn Toleubayeva
Shamshygaiyn Toleubayeva
This work is devoted to the analysis of the stress-strain state of the surfaced gear teeth using the T-Flex CAD software. The study showed that the surfaced teeth are able to withstand workloads, as well as loads increased by 50%, demonstrating a deformation of only 2%. Zones of maximum stresses and deformations have been identified, which makes it possible to predict the durability and reliability of the surfaced teeth. The conducted studies confirm the effectiveness of the electroslag surfacing method for restoring gears and its application to improve the performance of gears under high loads.

30 December 2024 in Science and Technology of Kazakhstan
Verified
Journal Article
Closed access
BSBaglan Smailova
Baglan Smailova
TBToty Buzauova
Toty Buzauova
IBI. A. Bartenev
I. A. Bartenev
DSD. A. Sarbayev
D. A. Sarbayev
JŠJelena Škamat
Jelena Škamat
The article focuses on the results of a study of the effect of electroslag surfacing modes on the penetration depth of restored teeth, conducted on the basis of a full factorial experiment (FFE) type 22. The welding current and the voltage on the slag bath were selected as factors. Each experiment was repeated three times, and the results were analyzed to build a regression model that takes into account all interactions of factors. The article describes in detail the process of encoding variable factors, constructing a planning matrix, calculating the coefficients of the regression equation and checking them for significance using the Student’s criterion. The adequacy of the experiment was confirmed by calculations using the Fisher criterion (Fcalculated<Ftable). According to the results of the experiment, it was found that the stress on the slag bath has the most significant effect on the total depth of penetration. The optimal mode has been determined (welding current 400 A and voltage on the slag bath 45 V), which provides the required penetration depth (4.63 mm) of a large-modulus tooth. The convergence of the results of the full-scale test with the results of planning a full factor experiment of type 22 was revealed, which made it possible to determine the optimal surfacing mode. This study can be used to optimize the parameters of electroslag surfacing, which will lead to an increase in the quality and efficiency of restoration of worn teeth. Keywords: electroslag surfacing, surfacing mode, penetration depth, welding current, welded tooth.

1 January 2025 in Journal of Applied Engineering Science
Verified
Journal Article
Open access
PDF file
TBToty Buzauova
Toty Buzauova
BSBaglan Smailova
Baglan Smailova
EMElena Malashkevichute-Brillant
Elena Malashkevichute-Brillant
The paper focuses on the calculation of cylindrical gear transmissions using analytical and numerical methods to determine contact and bending stresses. The results of analytical calculations are compared with numerical modeling data obtained using the Ansys Workbench software environment. A comparative analysis of the results is conducted, and discrepancies between the calculations are identified. Special attention is given to the analysis of stresses in surfaced gear teeth compared to solid ones. Unlike standard calculations for solid gears, this study focuses on the stress-strain state of surfaced teeth, taking into account their operational properties. For a more detailed analysis, the concept of the 'tooth contact angle position - ps' is introduced, which allowed for an in-depth investigation of its stress-strain state. The obtained results help identify the specific behavior of restored teeth under load, which is particularly relevant for developing gear transmission restoration technologies and assessing their durability. Considering the operational properties of surfaced teeth enables a more accurate evaluation of their strength characteristics. This study is aimed at assessing the strength properties of gear transmissions with surfaced teeth and can be used to optimize their design.

1 January 2025 in Journal of Applied Engineering Science
Verified
Journal Article
Open access
PDF file
TBToty Buzauova
Toty Buzauova
BSBaglan Smailova
Baglan Smailova
IBIgor Bartenev
Igor Bartenev
This study focuses on the restoration of large-module gear teeth of ball mills using the electroslag welding method, with an emphasis on practical results and mathematical modeling. The research established that optimal electroslag welding conditions are achieved by stabilizing key process parameters, such as current strength, slag bath voltage, and cooling water flow rate. For high-quality welding of gear teeth with a module of 20 mm, the following parameters are recommended: current strength I=362.5 A, slag bath voltage U=73.25-74 V, and water flow rate Qw=3-3.5 l/min. These parameters ensure minimal roughness and the required hardness of the welded teeth. Mathematical modeling provided equations linking welding modes with the roughness and hardness of the welded teeth. The presented experimental data are highly relevant for the scientific community and enterprises involved in the restoration of large-module gear wheels. The results hold significant practical value as they enable enterprises to reduce restoration costs and enhance the durability of components.

30 September 2024 in Science and Technology of Kazakhstan
Verified
Journal Article
Closed access
BSBaglan Smailova
Baglan Smailova
TBToty Buzauova
Toty Buzauova
IBI. A. Bartenev
I. A. Bartenev
JŠJelena Škamat
Jelena Škamat
This study examines the quality of a gear tooth surface fragment restored through electric arc welding. Visual inspection revealed a defect-free, dense surface. Macrostructure examination displayed uniformity and absence of cracks in the metal sample. The high hardness (HRC-36.61) of the weld deposit is crucial for wear resistance, while the base metal, with lower hardness (HRC-29.09), ensures ductility and impact toughness. Martensitic and residual austenitic structures in the weld deposit indicate deformation-resistant properties, with austenite providing good ductility and martensite contributing to high hardness and strength, making the material resistant to wear and deformation under dynamic loads. Thin lens-like martensitic plates and a reed-like structure suggest unique formation characteristics during electroslag welding’s oxidizing-reducing reactions. Microstructure analysis revealed a finer structure in the weld deposit compared to the base metal. The base metal exhibited a ferrite-pearlite structure typical of many steels, unchanged after welding. The weld deposit showed elevated carbon (0.70 %) and manganese (1.38 %) concentrations, typical for weld deposits, influencing mechanical properties. Elements like manganese and molybdenum enhance wear resistance, while the presence of chromium (0.42 %) and nickel (0.12 %) improves corrosion resistance, crucial in aggressive environments. Keywords: large-module gears, tooth wear, electro slag surfacing, hardness, analysis

25 December 2024 in Preprints.org
Verified
Preprint
Open access
PDF file
TBToty Buzauova
Toty Buzauova
BSBaglan Smailova
Baglan Smailova
YMYelena Iozasovna Malashkevichute-Brillant
Yelena Iozasovna Malashkevichute-Brillant
OOOmirzhan Oktyabrov
Omirzhan Oktyabrov
Stresses in surfaced gear teeth, particularly at the interface between the base metal and the surfaced layer, have consistently drawn scientific interest. However, a review of the literature revealed that these questions remain unanswered. Until now, the stress-strain state of surfaced gear teeth has not been thoroughly investigated. In this regard, the issues addressed in this article are both relevant and of significant scientific interest. The paper focuses on the calculation of cylindrical gear transmissions using analytical and numerical methods to determine contact and bending stresses. The results of analytical calculations are compared with numerical modeling data obtained using the Ansys Workbench software environment. A comparative analysis of the results is conducted, and discrepancies between the calculations are identified. Special attention is given to the analysis of stresses in surfaced gear teeth compared to solid ones. Unlike standard calculations for solid gears, this study focuses on the stress-strain state of surfaced teeth, taking into account their operational properties. For a more detailed analysis, the concept of the 'tooth contact angle position' is introduced, which allowed for an in-depth investigation of its stress-strain state. The obtained results help identify the specific behavior of restored teeth under load, which is particularly relevant for developing gear transmission restoration technologies and assessing their durability. Considering the operational properties of surfaced teeth enables a more accurate evaluation of their strength characteristics. This study is aimed at assessing the strength properties of gear transmissions with surfaced teeth and can be used to optimize their design.