Al Jumlat Ahmed

Al Jumlat Ahmed

Auto-generated profile, based on publicly available information

Al Jumlat Ahmed

CSIRO Technology Clayton Victoria Australia

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 May 2020 in ACS Applied Materials & Interfaces
Verified
Journal Article
Closed access
AAAl Jumlat Ahmed
Al Jumlat Ahmed
SHShahriar A. Hossain
Shahriar A. Hossain
SISheik Mohammad Kazi Nazrul Islam
Sheik Mohammad Kazi Nazrul Islam
FYFrank Yun
Frank Yun
GYGuangsai Yang
Guangsai Yang
Xiaotian WangXiaotian Wang
Xiaotian Wang

15 July 2020 in International Journal of Photoenergy
Verified
Journal Article
Open access
PDF file
RHRidwone Hossain
Ridwone Hossain
AAAl Jumlat Ahmed
Al Jumlat Ahmed
SISheik Md Kazi Nazrul Islam
Sheik Md Kazi Nazrul Islam
NSNirupam Saha
Nirupam Saha
PDPreetom Debnath
Preetom Debnath
MMM. A. Parvez Mahmud
M. A. Parvez Mahmud
Solar photovoltaic (PV) and solar thermal systems are most widely used renewable energy technologies. Theoretical study indicates that the energy conversion efficiency of solar photovoltaic gets reduced about 0.3% when its temperature increases by 1°C. In this regard, solar PV and thermal (PVT) hybrid systems could be a solution to draw extra heat from the solar PV panel to improve its performance by reducing its temperature. Here, we have designed a new type of heat exchanger for solar PV and thermal (PVT) hybrid systems and have studied the performance of the system. The PVT system has been investigated in comparison with an identical solar PV panel at outdoor condition at Dhaka, Bangladesh. The experiments show that the average improvement of open circuit voltage (Voc) is 0.97 V and the highest improvement of Voc is 1.3 V. In addition, the overall improvement of output power of solar PV panel is 2.5 W.

23 October 2019 in Royal Society Open Science
Verified
Journal Article
Open access
AAAl Jumlat Ahmed
Al Jumlat Ahmed
SISheik Md. Kazi Nazrul Islam
Sheik Md. Kazi Nazrul Islam
RHRidwone Hossain
Ridwone Hossain
JKJeonghun Kim
Jeonghun Kim
MKMinjun Kim
Minjun Kim
Xiaotian WangXiaotian Wang
Xiaotian Wang
Electron-doped SrTiO 3 is a well-known n -type thermoelectric material, although the figure of merit of SrTiO 3 is still inferior compared with p -type metal oxide-based thermoelectric materials due to its high lattice thermal conductivity. In this study, we have used a different amount of the non-ionic surfactant F127 during sample preparation to introduce nanoscale porosities into bulk samples of La-doped SrTiO 3 . It has been observed that the porosities introduced into the bulk sample significantly improve the Seebeck coefficient and reduce the thermal conductivity by the charge carrier and phonon scattering respectively. Therefore, there is an overall enhancement in the power factor (PF) followed by a dimensionless figure of merit ( zT ) over a wide scale of temperature. The sample 20 at% La-doped SrTiO 3 with 600 mg of F127 surfactant (SLTO 600F127) shows the maximum PF of 1.14 mW m −1 K −2 at 647 K which is 35% higher than the sample without porosity (SLTO 0F127), and the same sample (SLTO 600F127) shows the maximum value of z T is 0.32 at 968 K with an average enhancement of 62% in zT in comparison with the sample without porosity (SLTO 0F127).

27 February 2025 in Advanced Materials Technologies
Verified
Journal Article
Open access
AAAl Jumlat Ahmed
Al Jumlat Ahmed
JOJoseph F. Olorunyomi
Joseph F. Olorunyomi
SYShiqin Yan
Shiqin Yan
CEChristopher D. Easton
Christopher D. Easton
FZFarnaz Zadehahmadi
Farnaz Zadehahmadi
CDCara M. Doherty
Cara M. Doherty
A facile method of synthesizing flexible thin films of carbon nano dots (CNDs) and Polyvinyl Pyrrolidone (PVP) on cellulose based substrates is developed and their thermoelectric properties are demonstrated through the fabrication of a wearable device. Alongside enhanced thermoelectric performance, the CND thin films are biocompatible, low cost and scalable, all essential criteria for wearable thermoelectric devices. A critical window of the CND loading concentration on the cellulose‐based substrate is observed, with significantly enhanced Seebeck coefficient and Power Factor of thin films, demonstrating that the trade‐off principles for thermoelectric materials must be carefully tuned. The highest Seebeck coefficient of –358.45 µV·K−1, power factor of 0.03 µW·m−1·K−2 and the lowest thermal conductivity of 0.086 W·m−1·K−1 at room temperature is achieved with a CND loading concentration of 9.32 g cm−2. A wearable thermoelectric device is fabricated using n‐type CND films with copper electrodes. When worn, the device can generate voltage and current of ≈70 mV and ≈15 nA, respectively, at ΔT of 10 K.

15 March 2021 in Advanced Electronic Materials
Verified
Journal Article
Closed access
PDF file
AAAl Jumlat Ahmed
Al Jumlat Ahmed
DCDavid L. Cortie
David L. Cortie
FYFrank Fei Yun
Frank Fei Yun
YRYasir Rahman
Yasir Rahman
SISheik Md Kazi Nazrul Islam
Sheik Md Kazi Nazrul Islam
Xiaotian WangXiaotian Wang
Xiaotian Wang

1 May 2014
Verified
Conference Paper
Closed access
AAAl Jumlat Ahmed
Al Jumlat Ahmed
SPSathish P
Sathish P
Solid Oxide fuel cell (SOFC) is one of the potential sources of alternative energy. Investigation has been carried out to improve the power density of the intermediate temperature SOFC by optimizing the composition of the anode materials. Nickel Oxide (NiO) and Gadolinium doped Ceria (GDC) have been used as anode materials. And graphite has been used as a pore former in the anode substrate. Samples have been characterized successfully at three different operating temperatures (600, 550 and 500° C). The maximum open circuit voltage (0.86V) and peak power density (48.62 mW/cm 2 ) have been obtained from the sample with composition of NiO, GDC and graphite in 25, 50 and 25 volume % respectively.