This work focuses on modeling fatigue for aged asphalt mixtures. This is accomplished by combining existing models and adapting asphalt mixture aging laboratory procedures. The aging model used is based on the evolution of an internal state variable, and it is capable of taking into account the effect of aging temperature. The simplified viscoelastic continuum damage (S-VECD) model was selected for representing the fatigue damage behavior. Results at four aging states were analyzed, including the unaged mixture. Aged mixtures were obtained by heating loose asphalt mixture in an oven for two periods (2 and 45 days) and two temperatures (85 and 135°C). Based on the results from linear viscoelastic and S-VECD characterization, it was concluded that aging produces less damage tolerant materials; i.e., fatigue failure is observed for less evolved damage states. However, depending on the pavement conditions and on the pavement cross section geometry, because of the increase in material stiffness, aging ...
1 January 2018 in Road Materials and Pavement Design
Few information in the literature indicates how aging affects the service life of asphalt pavements. This work presents linear viscoelasticity and damage characterisation of an asphalt mixture at four aging states, and simulation of pavements fatigue performance. E* tests were performed in sinusoidal compression. Controlled crosshead tension-compression testing was used for damage characterisation. Aged materials were obtained by heating loose asphalt mixture at two temperatures (85°C and 135°C) and aging times (2 and 45 days). Two simulated pavements were studied for comparing behaviour at different ages using Layered Viscoelastic Pavement Analysis for Critical Distresses (LVECD). Results showed that the effect of aging seems to improve service life. It was also observed that simulating the asphalt layer as composed by two half-layers (aged at the top and unaged at the bottom) did not lead to significantly different results with respect to fatigue performance of an evenly aged layer.
Este artigo comparou a qualidade executiva das camadas de binder e capa de um revestimento asfáltico aplicado em uma rodovia federal sob quatro métricas distintas: valor médio da característica, variável aleatória da norma DNER-PRO 277/97 (por conveniência, tratada por PRO 277), percentual dentro dos limites (PDL) e desvio absoluto médio (DAM). Avaliou-se um conjunto de amostras referentes às propriedades grau de compactação, percentual de ligante asfáltico, volume de vazios, espessura e os percentuais passantes nas peneiras 3/4″, 1/2″, Nº 4 e Nº 200. Também se estimou o impacto da qualidade mensurada pelas medidas PDL e DAM na remuneração da empresa executora/contratada (fator de pagamento). De um modo geral, as indicações de aceitação ou rejeição da norma DNER-PRO 277/97 foram ratificadas na análise pelo PDL, não havendo na literatura uma análise equivalente para a medida DAM. Quanto ao pagamento variável em função da qualidade executiva, os equacionamentos obtidos na literatura apontam para divergências entre as recomendações de DAM e PDL. Por seu alinhamento com a norma DNER-PRO 277/97, o fator de pagamento baseado no PDL destaca-se como mais coerente e pode fundamentar uma proposta de remuneração variável vinculada aos padrões de qualidade conforme previsto nas leis nº 12.462/2011 (Regime Diferenciado de Contratações Públicas) e nº 14.133/2021 (Licitações e Contratos Administrativos). Assim, conclui-se que o indicador de qualidade tem potencial de adoção no cenário nacional como uma medida complementar ao critério da norma DNER-PRO 277/97.
This study evaluates the impact of asphalt pavement layer thickness variations on structural performance and life-cycle costs. Factors such as materials quality, traffic load, and construction precision affect durability, with layer thickness deviations causing earlier failures and increased life cycle costs. This research combines pavement performance prediction and life-cycle cost analysis (LCCA) of pavements designed by the California Bearing Ratio (CBR) method and the Brazilian mechanistic-empirical (M-E) method. Eight scenarios, including designed and as-built structures, were analyzed based on field-extracted cores. The Monte Carlo method simulated thickness variability, assessing its effect on performance and costs over 120 months, focusing on cracking evolution. The results showed that M-E designs are initially more expensive but offer superior long-term cost-benefit by reducing maintenance. A 10% increase in layer thickness resulted in less maintenance and 63% cost reduction, highlighting economic advantage of better designs. The analysis can include other factors and other M-E methods.