Recently, β-Ga2O3 solar-blind photodetectors (PDs) have been extensively investigated for a wide range of civil and military applications. Among them, the metal-semiconductor-metal (MSM) structure is one of the most popular candidates due to the merits of fabrication simplicity, the need for only one single-dopant active layer, easy integration with readout circuitry, high quantum efficiency, etc. However, there is generally a tradeoff between sensitivity and response speed due to the specific internal gain mechanism. In this work, MSM PDs based on the molecular beam epitaxy-grown β-Ga2O3 film were fabricated, and the metal/semiconductor (M/S) interfacial properties were tailored through the low-energy Ar-plasma pretreatment, resulting in the localized oxygen deficiency and a sharper interface. Accordingly, the PD sensitivity was dramatically improved, and the advantage of internal gain, i.e., high quantum efficiency, was preserved or became even larger. For example, the 60-W pretreated sample exhibited a high responsivity (R) of 8.41 A/W and a large specific detectivity (D*) of 1.24 × 1014 Jones, both increasing by one order of magnitude in comparison with the untreated sample. More interestingly, the response speed was unexpectedly accelerated, which is ascribed to the rapid and direct tunneling of electrons at the M/S interface as well as to the reduction in RC time constant based on the data analysis and the underlying physical principle discussion. The treatment conditions can be further optimized to counterbalance some side effects. These findings reveal an efficient technique for comprehensively improving the performance of β-Ga2O3 solar-blind PDs.
Recently, monoclinic Ga2O3 (β-Ga2O3) photodetectors (PDs) have been extensively studied for various commercial and military applications due to the merits of intrinsic solar rejection, high gain, and great compactness. In this work, c-plane sapphire substrates were annealed under different temperatures in a vacuum furnace prior to the molecular beam epitaxy (MBE) of β-Ga2O3 thin film, which yielded a smoother surface and even a terrace-and-step-like morphology on the substrate, resulting in improved crystallinity of the epitaxial film. Accordingly, both the dark and photo currents of β-Ga2O3 metal-semiconductor-metal (MSM) PDs were increased by the enhanced carrier mobility (μ) of the more crystalline film. However, the substrate-annealing temperature must be sufficiently high to offset the rise of the dark current and thus achieve a remarkable improvement in the photodetection properties. As a result, the PD fabricated on the 1050 °C-annealed substrate exhibited extremely high sensitivity, for example, high responsivity (R) of 54.9 A/W and large specific detectivity (D*) of 3.71 × 1014 Jones. Both parameters were increased by one order of magnitude because of the combined effects of the dramatic increase in μ and the effective reduction in defect-related recombination centers. Nevertheless, the latter also prolonged the recovery time of the PD. These findings suggest another way to develop β-Ga2O3 PD with extremely high sensitivity.
Underwater wireless optical communication (UWOC) can offer reliable and secure connectivity for enabling future internet-of-underwater-things (IoUT), owing to its unlicensed spectrum and high transmission speed. However, a critical bottleneck lies in the strict requirement of pointing, acquisition, and tracking (PAT), for effective recovery of modulated optical signals at the receiver end. A large-area, high bandwidth, and wide-angle-of-view photoreceiver is therefore crucial for establishing a high-speed yet reliable communication link under non-directional pointing in a turbulent underwater environment. In this work, we demonstrated a large-area, of up to a few tens of cm2, photoreceiver design based on ultraviolet(UV)-to-blue color-converting plastic scintillating fibers, and yet offering high 3-dB bandwidth of up to 86.13 MHz. Tapping on the large modulation bandwidth, we demonstrated a high data rate of 250 Mbps at bit-error ratio (BER) of 2.2 × 10−3 using non-return-to-zero on-off keying (NRZ-OOK) pseudorandom binary sequence (PRBS) 210-1 data stream, a 375-nm laser-based communication link over the 1.15-m water channel. This proof-of-concept demonstration opens the pathway for revolutionizing the photodetection scheme in UWOC, and for non-line-of-sight (NLOS) free-space optical communication.
Enhancing robustness and energy efficiency is critical in visible light communication (VLC) to support large-scale data traffic and connectivity of smart devices in the era of fifth-generation networks. To this end, we demonstrate that amorphous silicon (a-Si) thin-film solar cells with a high light absorption coefficient are particularly useful for simultaneous robust signal detection and efficient energy harvesting under the condition of weak light in this study. Moreover, a first-generation prototype called AquaE-lite is developed that consists of an a-Si thin-film solar panel and receiver circuits, which can detect weak light as low as 1 µW/cm2. Using AquaE-lite and a white-light laser, orthogonal frequency-division multiplexing signals with data rates of 1 Mb/s and 908.2 kb/s are achieved over a 20-m long-distance air channel and 2.4-m turbid outdoor pool water, respectively, under the condition of strong background light. The reliable VLC system based on energy-efficient a-Si thin-film solar cells opens a new pathway for future satellite-air-ground-ocean optical wireless communication to realize connectivity among millions of Internet of Things devices.
22 January 2021 in Journal of Physics D: Applied Physics
Group-III-nitride optical devices are conventionally important for displays and solid-state lighting, and recently have garnered much interest in the field of visible-light communication. While visible-light laser technology has become mature, developing a range of compact, small footprint, high optical power components for the green-yellow gap wavelengths still requires material development and device design breakthroughs, as well as hybrid integration of materials to overcome the limitations of conventional approaches. The present review focuses on the development of laser and amplified spontaneous emission (ASE) devices in the visible wavelength regime using primarily group-III-nitride and halide-perovskite semiconductors, which are at disparate stages of maturity. While the former is well established in the violet-blue-green operating wavelength regime, the latter, which is capable of solution-based processing and wavelength-tunability in the green-yellow-red regime, promises easy heterogeneous integration to form a new class of hybrid semiconductor light emitters. Prospects for the use of perovskite in ASE and lasing applications are discussed in the context of facile fabrication techniques and promising wavelength-tunable light-emitting device applications, as well as the potential integration with group-III-nitride contact and distributed Bragg reflector layers, which is promising as a future research direction. The absence of lattice-matching limitations, and the presence of direct bandgaps and excellent carrier transport in halide-perovskite semiconductors, are both encouraging and thought-provoking for device researchers who seek to explore new possibilities either experimentally or theoretically. These combined properties inspire researchers who seek to examine the suitability of such materials for potential novel electrical injection devices designed for targeted applications related to lasing and operating-wavelength tuning.