19 April 2017 in IEEE Journal of Solid-State Circuits
A novel phase-noise-filtering technique based on phase-domain averaging is proposed to suppress the large injection spurs and poor high-frequency phase noise of inductor-less injection-locked phase-locked loops (IL-PLLs). Demonstrated using a 1.2-GHz fractional-N IL-PLL based on a capacitive-ring-coupled ring oscillator, wideband spur-and-phase-noise suppression of up to 20 dB is achieved allowing for phase noise as low as -146 dBc/Hz at 30-MHz offset with a 2-MHz resolution. This allows for an inductor-less alternative to LC-based PLLs in scaled-digital CMOS technologies. The 65-nm CMOS prototype improves 10-MHz phase noise from -115 to -135 dBc/Hz, injection spurs from -40.5 to -57 dB, and integrated jitter from 3.57 to 1.48 ps while occupying an area of 0.6 mm₂ and consuming 19.8 mW from a 0.85-V supply, resulting in an FoM and FoMJitter of -163 and -223.6 dB, respectively.
23 December 2016 in IEEE Transactions on Circuits and Systems I: Regular Papers
A 4-element 60-GHz phased-array receiver RF front-end (RFE) employing LO-path phase-shifting configuration is presented. A wide bandwidth from 57 to 66 GHz is achieved by using multiple design techniques, including wide-band input matching network using on-chip baluns, peak-frequency staggering in the LNAs, and resonant-frequency tuning of the LC load in the first down-conversion stages. Furthermore, beamforming calibration is implemented by sequentially performing gain equalization, I/Q calibration and successive-approximation phase tuning. Implemented in a 65-nm CMOS process, each element measures gain of 21 dB and NF of 7.2 dB and IP₁dB of -21 dBm in high-gain mode while achieves IP₁dB of -12.5 dBm with gain of -2 dB and NF of 20 dB in low-gain mode. With beamforming calibration, the peak-to-null ratio of the synthesized 4-element array pattern is improved from 16.5 dB to 28.5 dB, corresponding to phase error of ±0.6° and amplitude mismatch of ±1.1 dB. The whole system consumes 320 mW from a 1.2-V supply and occupies a core area of 2.0 x 1.3 mm² excluding pads.
31 July 2017 in IEEE Journal of Solid-State Circuits
This paper presents an injected-locked THz radiator integrating a half-quadrature voltage-controlled oscillator (HQVCO), four injection-locked frequency quadruplers (ILFQs), and a chip-and-package distributed antenna (DA). At the system level, an architecture based on injection locking is employed to allow individual optimization of the output power and the phase noise. At the circuit level, intrinsic-delay compensation and harmonic boosting techniques are proposed to optimize the phase noise of the HQVCO and the output power of the ILFQs, respectively. The proposed DA composed of four exciting elements on silicon chip and a primary radiator in low-temperature co-fired ceramic (LTCC) package features a wide bandwidth of 13% and a gain of 3.8 dBi without using lens at 312 GHz. Implemented in a 65-nm CMOS process, the radiator system occupying a core area of 0.36 mm 2 achieves output frequency from 311.6 to 315.5 GHz and maximum equivalent isotropically radiated power (EIRP) of 10.5 dBm while consuming 300 mW. The output phase noise measures -109.3 dBc/Hz at 10-MHz offset and the dc-to-THz efficiency is 0.42%.
1 October 2013 in Solar Energy Materials and Solar Cells
20 December 2022 in IEEE Transactions on Circuits and Systems I: Regular Papers
This paper presents a millimeter-wave (mmW) frequency doubler based on complementary push-push (CPP) configuration achieving wideband, low-power and high-efficiency operation. Conventional push-push (PP) frequency doublers typically rely on half-wave rectification and suffer from performance compromise between the desired output and the DC current consumed. To mitigate this issue, a simple but effective CPP frequency doubling scheme is proposed to realize full-wave rectification, attaining enhanced output harmonic current and improved fundamental rejection without extra power consumption. At the output, an implicit dual-resonance (IDR) network featuring inherent resonant frequency alignment is employed to efficiently combine the harmonic power generated by the CPP transistors. Implemented in a 65-nm CMOS process and occupying a core area of 0.04 mm2, the proposed frequency doubler prototype measures conversion loss of < 10 dB from 53 to 78.5 GHz at 0-dBm input, while consuming 21.5 mW from a 1-V supply.
29 June 2018 in IEEE Journal of Solid-State Circuits
A rotated-phase-tuning (RPT) technique is proposed for millimeter-wave (mmW) LC -based oscillators. Without using varactors, the oscillation frequency is tuned by phase interpolation to vary the phase of the current flowing into the LC tank. Interestingly, the intrinsic delay of transistors is leveraged to rotate the phases for interpolation and thus to optimize the oscillator’s performance in terms of frequency tuning range and phase noise. Two E-band RPT oscillator prototypes are designed and implemented in a 65-nm CMOS process. The first one with four-phase output measures oscillation frequency from 67.8 to 81.4 GHz and phase noise of −108 to −113 dBc/Hz at 10-MHz offset, while consuming 13 to 25 mW from a 1-V supply. With similar power consumption, the second prototype featuring eight-phase output operates from 74.8 to 79 GHz and achieves phase noise of −116 to −118 dBc/Hz at 10-MHz offset. The four-phase and eight-phase oscillators occupy small core areas of 0.02 and 0.06 mm 2 , respectively.