Taehyun Kwon

Taehyun Kwon

Auto-generated profile, based on publicly available information

Taehyun Kwon

System LSI Division, Samsung Electronics, Hwaseong, South Korea

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 July 2020 in IEEE Transactions on Computers
Verified
Journal Article
Closed access
TKTaehyun Kwon
Taehyun Kwon
MIMuhammad Imran
Muhammad Imran
JYJoon-Sung Yang
Joon-Sung Yang
Next-generation memories have been actively researched to replace the existing memories like DRAM and flash in deep sub-micron process technology. Among the next-generation memories, Phase Change Memory (PCM) is seen as a good choice for future memory systems, given its good read performance, process compatibility and scaling potential. To enhance the storage density, multi-level cell (MLC) operation is seemed promising which can store more than one bit in each PCM cell. The use of heavyweight ECC comes at cost of significant degradations in storage density, performance and energy efficiency. In this paper, we propose a heterogeneous PCM architecture which uses both multi-level cell and single-level cell (SLC) together for a single word line. With highly-reliable SLC cells, the overall array reliability is enhanced. To improve the reliability further, a dynamic self-encoding/decoding scheme is performed before the data is written to the PCM cells. Since the proposed encoding/decoding scheme does not require any additional stages or storages for encoding and decoding, the overhead is negligible. The experimental results show that the reliability is improved approximately 10 $6$ times compared to conventional 4LC method. The performance and energy efficiency improvements are 21.5% and 30.3%, respectively.

26 March 2021 in IEEE Transactions on Computers
Verified
Journal Article
Closed access
MIMuhammad Imran
Muhammad Imran
TKTaehyun Kwon
Taehyun Kwon
NTNur A. Touba
Nur A. Touba
JYJoon-Sung Yang
Joon-Sung Yang
Phase Change Memory (PCM), with its better scaling potential compared to DRAM, is seen as a promising candidate to replace or complement DRAM. The heat generated from a RESET programming pulse to a PCM cell can disturb the neighboring cells which are not being programmed. Write disturbance (WD) poses a critical reliability challenge in high-density PCM memory with scaling below 20nm process technology node. Increasing the intra-cell space can eliminate the WD, however, it reduces the storage density which counteracts the benefits of scalability in PCM. At architectural level, a verify and correct (VnC) technique can be used to address this problem. However, this leads to an increased number of write operations, thus degrading performance, energy efficiency and memory lifetime. Due to its dependence on the type of programming operation and the state of the neighboring cell, WD is a data-dependent problem. Exploiting this property, encoding techniques have been proposed to reduce the frequency of WD-vulnerable data patterns. These techniques, however, do not eliminate the WD in an array and ultimately rely on the VnC method to ensure reliable memory operation. This article introduces a novel architecture, based on encoding and multi-level programming characteristics of PCM, to eliminate the intra-array WD in PCM. By eliminating WD and hence the need for a VnC operation, the proposed architecture improves performance, energy efficiency and memory lifetime. Our evaluation of the proposed architecture shows an average reduction of 57 percent in the number of writes (to service one write request) over the existing state-of-the-art intra-array WD-mitigation technique. Depending on the PCM write bandwidth, the proposed architecture can reduce the write service time by up to 27 percent, on average, compared to the existing best-performing technique. This leads to an average improvement of 15 percent in IPC. Additionally, by eliminating the overhead of a verify operation, the write energy efficiency is also improved by 8 percent over the previous art. Finally, with an average reduction of 26 percent in bit flips, the proposed method also improves the memory lifetime. The proposed method is also proven to be effective when considering WD both within the word-lines and across the bit-lines.

25 March 2021 in IEEE Transactions on Computer-Aided Design of Integrated Circuits and Systems
Verified
Journal Article
Closed access
MIMuhammad Imran
Muhammad Imran
TKTaehyun Kwon
Taehyun Kwon
JYJoon-Sung Yang
Joon-Sung Yang
Phase change memory (PCM) is an emerging, resistance-based, nonvolatile memory. With a promising scaling potential, PCM can replace the existing charge-based memory technologies. A highly scaled PCM is prone to write disturbance (WD) because of a high-current RESET programming pulse. Exploiting the data-dependent nature of WD, encoding techniques have been proposed to reduce the frequency of WD-vulnerable data patterns. These techniques work along with a verify and correct (VnC) method to ensure memory reliability. However, the effectiveness of these techniques varies depending on the data patterns. Unlike the conventional methods, this article introduces a WD-aware programming technique to mitigate WD in PCM. The proposed method encodes the data based on the number of WD-vulnerable cells and the bit flips. By reducing the number of WD-vulnerable cells as well as the bit flips, the proposed method is more effective than the existing encoding techniques, in mitigating WD as well as improving the memory lifetime. Evaluation using various realistic workloads shows that the proposed method can reduce the average word-line WD errors by 62%, compared to the existing state of the art. With a reduced number of WD errors, the frequency of a VnC operation is also reduced. This leads to a reduction of 44% in the number of extra writes and 20% in the average write time. With reduction in the number of writes and the write time, instructions-per-cycle is improved by 9% and the write energy by 11% over the existing art. By reducing the number of bit flips compared to the previous state of the art, the proposed method improves the PCM memory lifetime by 13% to 33%, considering the asymmetry of SET and RESET operations in impacting the cell endurance.

9 July 2019 in IEEE Transactions on Computer-Aided Design of Integrated Circuits and Systems
Verified
Journal Article
Closed access
TKTaehyun Kwon
Taehyun Kwon
MIMuhammad Imran
Muhammad Imran
JYJoon-Sung Yang
Joon-Sung Yang
With the scaling limitations and increasing leakage power of the existing charge-based memories, next-generation memory technologies to overcome the issues are in development. Among the various emerging memories, Phase Change Memory (PCM) is considered as a promising candidate due to its scalability potential and negligible leakage power. For enhanced storage density, the multi-level cell (MLC) operation has been proposed for PCM. This, however, comes at cost of poor reliability, write energy increase and performance degradation. Unlike DRAM, the MLC PCM has a much higher soft error rate due to the resistance drift phenomenon. Error correction code (ECC) schemes can be utilized to improve the MLC PCM reliability, however, this would lead to a lower storage density and an increase in write energy and latency. The iterative programming required for the MLC PCM also degrades its energy efficiency and performance. This paper introduces a simple yet effective encoding scheme to mitigate the problems of the MLC PCM. By using a simple XOR-based encoding, the proposed architecture minimizes the most drift-prone state in the data. The method divides the original data into several encoding blocks and analyzes initial pattern frequencies for each 2-bit pattern. Based on the initial pattern frequencies, the inputs for the XOR encoding are selected that result in minimal frequency of the drift-prone state. This considerably enhances the MLC PCM reliability, leading to a high storage density with a reduced ECC overhead. The energy efficiency and performance are also improved due to reduction in iterative current pulses and ECC overhead. Simulation results show a reduction of about 105X in soft error rate. The improvements in energy efficiency and performance over the conventional 4-level cell (4LC) PCM are 11.5% and 31.9%, respectively.

21 February 2020 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
Verified
Journal Article
Closed access
TKTaehyun Kwon
Taehyun Kwon
MIMuhammad Imran
Muhammad Imran
DPDavid Z. Pan
David Z. Pan
JYJoon-Sung Yang
Joon-Sung Yang
Clock network plays the most significant role in power consumption in IC design. Since a clock network normally has a high switching ratio, power optimization of the clock network is one of the best solutions to minimize dynamic power and total power in modern IC designs. The clock network is synthesized based on an initial flip-flop placement. The number of clock buffers and their sizes are decided by the initial placement. Moreover, clock wires, which are the major sources of clock power consumption, are also constructed based on the flip-flop placement. As a result, the flip-flop placement determines the quality of the clock network. In this article, we propose a new clock network optimization method to reduce the dynamic power consumption of clock network. The method first creates virtual tiles over the entire design area and selects the most effective columns to align flip-flops in lines. Once the effective columns are determined, flip-flops are relocated based on the virtual tiles in the columns considering the minimum moving distance. By aligning flip-flops, it is possible to significantly reduce both wire capacitance and wire length. Since it does not change the clock structure, unlike the conventional clock network optimization techniques which use multibit flip-flop or register bank, there is no degradation in timing or other constraints. Experimental results show that the proposed method reduces the wire capacitance, wire length, and via count up to 23.2%, 10.2%, and 16.4%, respectively, in five industrial intellectual property (IP) designs. The reduction in clock network power is 14.1% on average.