1 March 2025 in Applied Physics Letters
We describe the short-term frequency stability characterization of external-cavity diode lasers stabilized onto the 6S1/2−7P1/2 transition of Cs atoms at 459 nm, using a microfabricated vapor cell. The laser beatnote between two nearly identical systems, each using saturated absorption spectroscopy in a simple retroreflected configuration, exhibits an instability of 2.5 × 10−13 at 1 s, consistent with phase noise analysis, and 3 × 10−14 at 200 s. The primary contributors to the stability budget at 1 s are the FM-AM noise conversion and the intermodulation effect, both emerging from laser frequency noise. These results highlight the potential of microcell-based optical references to achieve stability performances comparable to that of an active hydrogen maser in a remarkably simple architecture.
19 December 2024 in Journal of the Optical Society of America B
We report on the development and short-term stability characterization of an optical frequency reference based on the spectroscopy of the rubidium two-photon transition at 778 nm in a microfabricated vapor cell. When compared against a 778 nm reference signal extracted from a frequency-doubled cavity-stabilized telecom laser, the short-term stability of the microcell frequency standard is 3.5×10−13τ−1/2 until 200 s, in good agreement with a phase noise level of +43dBrad2/Hz at 1 Hz offset frequency. The two main contributions to the short-term stability of the microcell reference are currently the photon shot noise and the intermodulation effect induced by the laser frequency noise. Retaining a relevant margin of progress, these results show the interest of this spectroscopic approach for the demonstration of high-stability miniaturized optical vapor cell clocks. Such clocks are poised to be highly beneficial for applications in navigation, communications, and metrology.
1 June 2023 in Journal of Applied Physics
The stability and accuracy of atomic devices can be degraded by the evolution of their cell inner atmosphere. Hence, the undesired entrance or leakage of background or buffer gas, respectively, that can permeate through the cell walls, should be slowed down. In this work, we investigate helium permeation in microfabricated alkali vapor cells filled with He and whose windows are made of borosilicate glass (BSG) or aluminosilicate glass (ASG). The permeation is then derived from routine measurements of the pressure-shifted hyperfine transition frequency of an atomic clock. We first confirm that ASG reduces the He permeation rate by more than two orders of magnitude, in comparison to BSG. In addition, we demonstrate that Al2O3 thin-film coatings, known to avoid alkali consumption in vapor cells, can also significantly reduce He permeation. The permeation through BSG is thereby reduced by a factor up to 130, whereas the one through ASG is decreased by a factor up to 5.0 compared to uncoated substrates. These results may contribute to the development of miniaturized atomic clocks and sensors with improved long-term stability or sensitivity.
11 March 2024 in Applied Physics Letters
We report on the operation of a coherent population trapping (CPT) microcell atomic clock using a pulsed Ramsey-like interrogation. The Ramsey-CPT sequence, defined by two-step optical pulses separated by a free-evolution dark time, is produced by switching on and off the output power of a low-power vertical-cavity surface-emitting laser, through direct modulation of its driving current. High-contrast and narrow Ramsey-CPT fringes are detected without the use of any external optical modulator stage. We demonstrate closed-loop operation of the clock based on high-speed digital signal processing implemented in a field programmable gate array board. The clock's short-term fractional frequency stability is 1.3 × 10−10τ−1/2 until 2000 s. A power light-shift coefficient of 8 × 10−11/μW, in relative value, is obtained for a dark time of 150 μs. This value is about ten times lower than in the continuous regime. These results show the feasibility of fully integrated atomic clocks based on Ramsey spectroscopy, which could provide enhanced long-term stability.
27 August 2024 in Journal of Applied Physics
Stability and precision of atomic devices are closely tied to the quality and stability of the internal atmosphere of the atomic vapor cells on which they rely. Such an atmosphere can be stabilized by building the cell with low permeation materials such as sapphire or aluminosilicate glass in microfabricated devices. Recently, we have shown that permeation barriers made of Al2O3 thin-film coatings deposited on standard borosilicate glass could be an alternative for buffer gas pressure stabilization. In this study, we, hence, investigate how helium permeation is influenced by the thickness, ranging from 5 to 40 nm, of such Al2O3 thin films coated by atomic layer deposition. Permeation rates are derived from long-term measurements of the pressure-shifted transition frequency of a coherent population trapping (CPT) atomic clock. From thicknesses of 20 nm onward, a significant enhancement of the cell hermeticity is experienced, corresponding to two orders of magnitude lower helium permeation rate. In addition, we test cesium vapor cells filled with neon as a buffer gas and whose windows are coated with 20 nm of Al2O3. As for helium, the permeation rate of neon is significantly reduced, thanks to alumina coatings, leading to a fractional frequency stability of 4×10−12 at 1 day when the cell is used in a CPT clock. These features outperform the typical performances of uncoated Cs–Ne borosilicate cells and highlight the significance of Al2O3 coatings for buffer gas pressure stabilization.
1 April 2025 in Applied Physics Letters
Microfabricated alkali vapor cells are key to enable miniature devices such as atomic clocks and optically pumped magnetometers with reduced size, weight, and power. Yet, more versatile fabrication methods are still needed to further expand their use cases. Here, we demonstrate an approach to collectively fill and seal microfabricated cesium cells using locally sealed microchannels patterned within one of the glass substrates comprising the cells. Unlike current methods that rely on wafer-level anodic bonding as the last sealing step, an approach based on local sealing opens the path to features so far limited to traditional glass-blown cells, including the ability to deposit temperature-sensitive antirelaxation coatings, reaching lower background gas pressure without an additional gettering material or filling with diverse atomic or molecular species.