The thermionic emission mechanism is usually employed to model the charge packet which is not affected by the potential barrier, however, the electric fields induced by the charge itself are not included in previous work. We introduce a proposed physical-based model to characterize the whole charge behavior characteristics of the pinned photodiode (PPD) when employing the thermal diffusion, self-induced drifting, and thermionic emission mechanisms together. In addition, the dynamic PPD parameters such as PPD capacitance ( C PPD ), PPD potential ( V PPD ), and charge transfer potential barrier ( V B ) are included to characterize the integration and transfer process together based on iterative methods. The model is verified with technology computer-aided design (TCAD) simulations and the test devices were fabricated in a 0.11 μm CMOS image sensor (CIS) process. The proposed analytical behavior model presents a great convenience for circuit-level simulation of the PPD-based pixels.
6 October 2023 in IEEE Transactions on Instrumentation and Measurement
This paper proposes a low power 320×240 indirect time of flight (i-ToF) vision system with non-linearity self-calibration technique. A pump gate modulator (PGM) technique is applied in the pixel to reduce the power consumption of pixel modulation. As a result, the pixel has a higher lateral electric field in lower voltage swing of modulation and the pixel can operate in the depletion state to achieve smaller load capacitance. To improve the non-linearity of the sensor, non-linearity self-calibration techniques are proposed. It includes channel toggle technique and pre-distortion single slop analog-to-digital converter (SS-AdC) which eliminates the quadratic non-linearity in the readout channel and source follower (SF) non-linearity in the pixel, respectively. Furthermore, it reduces the difficulty of nonlinear calibration of different batches of chips. The measured non-linearity decreases greatly without back-end calibration, which is smaller than 0.8 % within the distance range from 0.12 m to 5 m. The receiver chip is fabricated in 110 nm front-side illuminated (FSI) process with 5.6 μm×5.6 μm pixel size. The chip power is only 130 mW.
26 May 2026 in IEEE Transactions on Instrumentation and Measurement
Time walk error significantly impacts the accuracy of distance measurements in direct time-of-flight (d-ToF) LiDAR systems. A system-level d-ToF model that comprehensively accounts for the mechanisms is established in this paper. Then, an active multi-power excitation (AMPE) strategy is proposed and verified in a silicon photomultiplier (SiPM)-based d-ToF LiDAR. Compared with conventional passive correction methods, AMPE actively injects known excitation constraints into the measurement process. It exploits the relationship between emission energy and threshold-crossing time by transmitting pulses with controlled power using a customized compensation algorithm. The core strength of this method is that it transforms the correction problem into a constrained estimation problem governed by emission control, thereby avoiding complex receiver-side timing circuitry and extensive offline calibration. A prototyped LiDAR system is developed, and experimental results demonstrate that more than a 72% reduction in walk error induced depth distortion is achieved with only 10 measurements per range point, enabling reliable 200 m operation under 60 klux ambient illumination. The proposed method establishes a novel time walk error compensation strategy, enhancing the energy efficiency and wide dynamic range of d-ToF LiDAR applications.
3 August 2023 in IEEE Transactions on Electron Devices
This article presents a 3.5 $\mu$ m stacked backside-illuminated (BSI) indirect time-of-flight (i-ToF) pixel fabricated in a 65-nm CMOS image sensors (CIS) process. Transfer gate-induced lateral electric field control of charge transfer is one of the most relied techniques for implementing i-ToF image sensors. However, the transfer gate as modulated gate usually needs a high voltage swing to achieve high demodulation contrast (DC). We introduce a photonic demodulator pixel that utilizes a new lateral electric field modulation technology to achieve a 1.0 V modulation voltage swing while maintaining a high DC of 86% at 100 MHz modulation frequency. The proposed method employs a gate-controlled junction field effect transistor (JFET) to control the drain-induced barrier lowering (DIBL) effect to modulate the lateral electric field. In addition, the photonic demodulator can be also fully depleted with an N-type epitaxy for 22% quantum efficiency (QE) enhancement at 940 nm. This development can greatly lower the power consumption for high-resolution i-ToF sensor applications.
1 October 2026 in IEEE Transactions on Biomedical Circuits and Systems
This work presents a PET-oriented double-ring Vernier time-to-digital converter (DRVTDC) that targets the timing-quantization block required in multi-voltage-threshold (MVT) and time-over-threshold (ToT) front-end readout for time-of-flight (ToF) positron emission tomography (PET) applications. This work addresses two critical error mechanisms that limit the use of multi-stage Vernier TDCs: parallel output misalignment (POM) between quantization stages and mismatch-induced chasing error (MCE) in the Vernier arbiter array. To suppress these errors, a joint calibration scheme combining code error cancellation (CEC) and Vernier arbiter phase calibration (VAPC) is proposed. The core TDC achieves a 10.4-ps resolution with only 0.0075 mm2 core area. The implemented 7-bit coarse counter provides a dynamic range (DR) of 5.12 μs. Empowered by these techniques, the measured DNL and INL ranges are significantly improved from +3.17/-0.89 LSB and +7.0/-6.9 LSB to +0.34/-0.29 LSB and +1.15/-1.09 LSB, respectively, alongside a 26-dB enhancement in the SFDR. The core TDC consumes 1.758 mW, with a total of 5.526 mW including the PLLs.
1 January 2026 in IEEE Transactions on Circuits and Systems II: Express Briefs