Edward Guzik

Edward Guzik

Auto-generated profile, based on publicly available information

Edward Guzik

Faculty of Foundry Engineering, AGH University of Science and Technology, Al. A. Mickiewicza 30, 30-059 Kraków, Poland

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 July 2023 in Materials
Verified
Journal Article
Open access
PDF file
Karolina Bracka-KęsekKarolina Bracka-Kęsek
Karolina Bracka-Kęsek
ASAndrzej Szczęsny
Andrzej Szczęsny
EGEdward Guzik
Edward Guzik
DKDariusz Kopyciński
Dariusz Kopyciński
Faced with the raw material crisis in Zn resources, researchers are facing the challenge of developing technology for producing zinc coatings that are thinner than those that have been produced to date. This would make it possible to reduce Zn consumption in the hot-dip galvanisation process. The study included an experiment that involved dip galvanising steel samples in baths of different Ti concentrations; this process was carried out at 450 °C and 550 °C. The use of this additive made it possible to reduce the growth of the alloy layer in the obtained zinc coatings. Using an optical microscope, observations were made of the microstructures of the resulting coatings, which made it possible to determine the thickness of the alloy layer in the coating. Thanks to the use of scanning electron microscopy with EDS analysis, however, it was possible to plot the chemical composition of the studied coatings and accurately observe the morphology of the formed phases. An intermetallic Zn-Fe-Ti phase was observed in the coatings formed in a Ti-added bath, which can affect the growth inhibition of the alloy layer in the zinc coating.

8 September 2022 in Materials
Verified
Journal Article
Open access
PDF file
DSDorota Siekaniec
Dorota Siekaniec
DKDariusz Kopyciński
Dariusz Kopyciński
ETEdward Tyrała
Edward Tyrała
EGEdward Guzik
Edward Guzik
ASAndrzej Szczęsny
Andrzej Szczęsny
This paper presents a comprehensive approach to optimising the structure and properties of chromium cast iron that is intended for use in the production of castings that operate under abrasive-wear conditions. In the study, chromium cast iron was inoculated to reduce the grain size in the solidification structure. The finer-grained structure of the casting has a positive effect on its mechanical properties. A number of inoculants have been used that allow the elimination of many types of casting defects: hot cracks and porosities that often occur during the production of chromium cast iron castings. Another advantage of the developed inoculation procedure is the resulting increase in the toughness of chromium cast iron. It should be emphasised that this cast iron does not have a high impact strength in its as-cast condition due to the formation of chromium carbides in the structure. This work also proposes a specially designed heat treatment for inoculated cast iron. The parameters of the applied heat treatment were determined on the basis of dilatometric tests. The visible deviation on a dilatogram at a temperature of about 600 °C is the result of a partial martensitic transformation in the area of grain boundaries. Therefore, the increase in abrasion resistance chromium cast iron is mainly due to the appearance of martensite. The microstructure of the investigated cast iron is particularly desirable in the case of alloys that work with lubrication. The microcavities that are formed by the abrasion of the softer phase constitute natural grease, which reduces abrasive wear. Under the influence of heat treatment, only a part of austenite located near the carbides is destabilized and transformed into martensite. Therefore, this phase of composition formation provided much greater resistance to abrasive wear and hardness.

5 November 2021 in Materials
Verified
Journal Article
Open access
PDF file
JDJózef Dorula
Józef Dorula
DKDariusz Kopyciński
Dariusz Kopyciński
EGEdward Guzik
Edward Guzik
ASAndrzej Szczęsny
Andrzej Szczęsny
DGDaniel Gurgul
Daniel Gurgul
Inoculation of cast iron has become a commonly used metallurgical process, which is carried out in a foundry in order to improve the mechanical properties of utility alloys. It consists in changing the physicochemical state of the melted alloy. This change is caused by the introduction of cast iron with a low ability to nucleate graphite, shortly before pouring a small mass of the substance—an inoculant that increases the number of active nuclei. It is also justified that the literature often connects an increase in the tensile strength UTS of the inoculated grey cast iron, with changes in the characteristics of the particles of graphite. However, in strongly hypoeutectic cast iron, in which a large number of primary austenite grains crystallize, the interdendritic distribution of graphite is usually the result. It also follows that the nature of the graphite precipitates is determined by the mutual relations between the interfacial distances in eutectic grains and the interdendritic distances in the grains of primary austenite occurring in the Fe–C alloys. The article presents the influence of the inoculant on the characteristics of the precipitation of primary austenite grains in relation to the sulphur content in grey cast iron with flake graphite. The study also showed that primary grains in grey cast iron have a great influence on mechanical properties, such as the tensile strength UTS. In this case, the key is to know the value of the degree of undercooling ΔT. The type of inoculant used affects the ΔT value. The study related the number of N primary austenite grains with the degree of undercooling ΔT and the tensile strength UTS with the number of primary austenite N grains.

9 September 2022 in Materials
Verified
Journal Article
Open access
PDF file
JDJózef Dorula
Józef Dorula
DKDariusz Kopyciński
Dariusz Kopyciński
EGEdward Guzik
Edward Guzik
ASAndrzej Szczęsny
Andrzej Szczęsny
This study shows that the inoculation process of a molten alloy is crucial in disposing of porosity-type defects. A thermal analysis is used to assess the physico-chemical state of a molten alloy, which can be an indicator of the inoculation effect. A modern thermal analysis should be able to perform a quick data-analysis and provide information about any possible problems in a casting if it is poured with the analysed alloy. The time of the transmission of this information depends on whether we can make a decision and introduce changes to the metallurgical process. An important piece of information that can be obtained in this way is a message about the possibility of the appearance of porosity in a cast iron casting. In such a situation, an operator can react by applying an additional dose of inoculant. The porosity that is indicated by the thermal analysis systems can be either gaseous or shrinkage in nature. The research that is presented in this paper is based on two industrial castings that are made of cast iron with reduced sulphur content, in which shrinkage porosity occurred and was detected during the mechanical machining of the castings. As a result of laboratory tests in which iron powder was introduced along with an inoculant, a mixture was developed that, when applied under industrial conditions, eliminated the porosity defects by increasing the number of austenite dendrites. The ITACA thermal analysis system was used at each stage of the research, which allowed for the faster and more precise determination of the appropriate amount of the inoculant mixture that was used.

19 April 2023 in Materials
Verified
Journal Article
Open access
PDF file
EGEdward Guzik
Edward Guzik
DKDariusz Kopyciński
Dariusz Kopyciński
ABAndriy Burbelko
Andriy Burbelko
ASAndrzej Szczęsny
Andrzej Szczęsny
The treatment of inoculation of white cast iron with carbide precipitations that consist of increasing the number of primary austenite grains is not as well-known as the treatment of inoculation of gray cast iron in which the number of eutectic grains increases. In the studies included in the publication, experiments were carried out using the addition of ferrotitanium as an inoculant for chromium cast iron. The Cellular Automaton Finite Elements (CAFE) module of ProCAST software was used in order to analyze the formation of the primary structure of hypoeutectic chromium cast iron in a casting of various thicknesses. The modeling results were verified using Electron Back-Scattered Diffraction (EBSD) imaging. The obtained results confirmed obtaining a variable number of primary austenite grains in the cross-section of the tested casting, which significantly affects the strength properties of the obtained chrome cast iron casting.

12 October 2021 in Materials
Verified
Journal Article
Open access
PDF file
RGRobert Gilewski
Robert Gilewski
DKDariusz Kopyciński
Dariusz Kopyciński
EGEdward Guzik
Edward Guzik
ASAndrzej Szczęsny
Andrzej Szczęsny
A suitable aluminum additive in cast iron makes it resistant to heat in a variety of environments and increases the abrasion resistance of the cast iron. It should be noted that high-aluminum cast iron has the potential to become an important eco-material. The basic elements from which it is made—iron, aluminum and a small amount of carbon—are inexpensive components. This material can be made from contaminated aluminum scrap, which is increasingly found in metallurgical scrap. The idea is to produce iron castings with the highest possible proportion of aluminum. Such castings are heat-resistant and have good abrasive properties. The only problem to be solved is to prevent the activation of the phenomenon of spontaneous decomposition. This phenomenon is related to the Al4C3 hygroscopic aluminum carbide present in the structure of cast iron. Previous attempts to determine the causes of spontaneous disintegration by various researchers do not describe them comprehensively. In this article, the mechanism of the spontaneous disintegration of high-aluminum cast iron castings is defined. The main factor is the large relative geometric dimensions of Al4C3 carbide. In addition, methods for counteracting the phenomenon of spontaneous decay are developed, which is the main goal of the research. It is found that a reduction in the size of the Al4C3 carbide or its removal lead to the disappearance of the self-disintegration effect of high-aluminum cast iron. For this purpose, an increased cooling rate of the casting is used, as well as the addition of elements (Ti, B and Bi) to cast iron, supported in some cases by heat treatment. The tests are conducted on the cast iron with the addition of 34–36% mass aluminum. The molten metal is superheated to 1540 °C and then the cast iron samples are cast at 1420 °C. A molding sand with bentonite is used to produce casting molds.