Daniel Rademacher

Daniel Rademacher

Auto-generated profile, based on publicly available information

Daniel Rademacher

Fraunhofer Institute for Surface Engineering and Thin Films, Bienroder Weg 54E, 38108 Braunschweig, Germany

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2015 in Surface and Coatings Technology
Verified
Journal Article
Closed access
MVMichael Vergöhl
Michael Vergöhl
SBStefan Bruns
Stefan Bruns
DRDaniel Rademacher
Daniel Rademacher
GBGünter Bräuer
Günter Bräuer

28 February 2012 in Applied Optics
Verified
Journal Article
Closed access
PDF file
DRDaniel Rademacher
Daniel Rademacher
BFBenjamin Fritz
Benjamin Fritz
MVMichael Vergöhl
Michael Vergöhl
Particles generated during reactive magnetron sputtering cause defects in optical thin films, which may lead to losses in optical performance, pinholes, loss of adhesion, decreased laser-induced damage thresholds and many more negative effects. Therefore, it is important to reduce the particle contamination during the manufacturing process. In the present paper, the origin of particles during the deposition of various oxide films by midfrequency pulsed reactive magnetron sputtering was investigated. Several steps have been undertaken to decrease the particle contamination during the complete substrate handling procedure. It was found that conditioning of the vacuum chamber can help to decrease the defect level significantly. This level remains low for several hours of sputtering and increases after 100 hours of process time. Particle densities of SiO2 films deposited with cylindrical and planar dual magnetrons at different process parameters as well as different positions underneath the target were compared. It was observed that the process power influences the particle density significantly in case of planar targets while cylindrical targets have no such strong dependence. In addition, the particle contamination caused by different cylindrical target materials was analyzed. No major differences in particle contamination of different cylindrical target types and materials were found.

9 December 2012 in Thin Solid Films
Verified
Journal Article
Closed access
DRDaniel Rademacher
Daniel Rademacher
TZTobias Zickenrott
Tobias Zickenrott
MVMichael Vergöhl
Michael Vergöhl

21 January 2014 in Applied Optics
Verified
Journal Article
Closed access
SBStefan Bruns
Stefan Bruns
DRDaniel Rademacher
Daniel Rademacher
MVMichael Vergöhl
Michael Vergöhl
PWPeter Weiss
Peter Weiss

20 December 2010 in Applied Optics
Verified
Journal Article
Closed access
PDF file
DRDaniel Rademacher
Daniel Rademacher
MVMichael Vergöhl
Michael Vergöhl
URUwe Richter
Uwe Richter
An in situ monitoring setup and process control loop were developed and integrated into a magnetron sputtering coater equipped with a Sentech SE 401 single wavelength ellipsometer, including the engineering of software for in situ process control to enhance production accuracy. By using that software, the system allows direct monitoring of the layer thickness on a moving substrate. It is shown that it is possible to determine the complex index of refraction from the distribution of measurements depending on the layer thickness. A strategy has been developed for in situ reverse thickness engineering of the top layers to compensate measurement errors.

20 November 2012 in Applied Optics
Verified
Journal Article
Closed access
PDF file
DRDaniel Rademacher
Daniel Rademacher
GBGünter Bräuer
Günter Bräuer
BFBenjamin Fritz
Benjamin Fritz
MVMichael Vergöhl
Michael Vergöhl
In this paper different SiO2-TiO2 mixtures are prepared by metallic mode reactive sputtering. The samples were sputtered from cylindrical targets in a sputter-up configuration using an additional plasma source for oxidization. The different ratios of SiO2 and TiO2 in the mixtures are prepared by a target sputtering power variation. Optical film properties of the mixtures such as refractive index, which is determined by ellipsometric measurements, and optical bandgap, which is measured by photometric (transmission) measurements, are investigated. The thin-film structure is investigated by x-ray diffraction analysis and the stress of the films is presented. It is shown that the metallic mode reactive sputtering in the present configuration is applicable to continuously tune optical and mechanical properties. Finally the sputtered mixed materials are compared with other optical standard materials such as Nb2O5, Ta2O5, HfO2, and Al2O3.