Binod Kumar Kanaujia

Binod Kumar Kanaujia

Auto-generated profile, based on publicly available information

Binod Kumar Kanaujia

Department of Electronics and Communication Engineering, Dr. B. R. Ambedkar National Institute of Technology, Jalandhar, India

Research Focus & Metrics

Academic Career Length

25Years (2002-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2017 in International Journal of Antennas and Propagation
Verified
Journal Article
Open access
PDF file
MKMukesh Kumar Khandelwal
Mukesh Kumar Khandelwal
BKBinod Kumar Kanaujia
Binod Kumar Kanaujia
Sachin KumarSachin Kumar
Sachin Kumar
Slots or defects integrated on the ground plane of microwave planar circuits are referred to as Defected Ground Structure. DGS is adopted as an emerging technique for improving the various parameters of microwave circuits, that is, narrow bandwidth, cross-polarization, low gain, and so forth. This paper presents an introduction and evolution of DGS and how DGS is different from former technologies: PBG and EBG. A basic concept behind the DGS technology and several theoretical techniques for analysing the Defected Ground Structure are discussed. Several applications of DGS in the field of filters, planar waveguides, amplifiers, and antennas are presented.

30 January 2013 in IEEE Antennas and Wireless Propagation Letters
Verified
Journal Article
Closed access
AGAnil Kr Gautam
Anil Kr Gautam
SYSwati Yadav
Swati Yadav
BKBinod Kr Kanaujia
Binod Kr Kanaujia
A novel coplanar waveguide (CPW)-fed compact ultrawideband (UWB) microstrip antenna is proposed for ultrawideband applications. The proposed antenna posseses a method to minimize the monopole antenna by loading of inverted L-strip over the conventional monopole patch antenna to lower the height of the antenna. The ground was vertically extended toward two sides of the single radiator. Therefore, the large space around the radiator that is usually wasted can be effectively saved. The antenna is practically fabricated and simulated. Measured results show a good agreement with simulated results. The prototype with overall size of $25 \times 25 \times 1.6\ {\hbox{mm}}^3$ achieves good impedance matching, constant gain, stable radiation patterns, and constant group delay over an operating bandwidth of 2.6-13.04 GHz (10.44 GHz).

1 October 2019 in AEU - International Journal of Electronics and Communications
Verified
Journal Article
Closed access
Rakesh Nath TiwariRakesh Nath Tiwari
Rakesh Nath Tiwari
PSPrabhakar Singh
Prabhakar Singh
BKBinod Kumar Kanaujia
Binod Kumar Kanaujia
KSKunal Srivastava
Kunal Srivastava

29 December 2015 in IEEE Transactions on Antennas and Propagation
Verified
Journal Article
Closed access
AGAnil Kumar Gautam
Anil Kumar Gautam
LKLalit Kumar
Lalit Kumar
BKBinod Kumar Kanaujia
Binod Kumar Kanaujia
KRKarumudi Rambabu
Karumudi Rambabu
This communication presents a small, low-profile planar triple-band microstrip antenna for WLAN/WiMAX applications. The goal of this communication is to combine WLAN and WiMAX communication standards simultaneously into a single device by designing a single antenna that can excite triple-band operation. The designed antenna has a compact size of $19 \times 25\;\text{mm}^{2}$ ($0.152 \lambda_{0}\;\times 0.2 \lambda_{0}$). The proposed antenna consists of F-shaped slot radiators and a defected ground plane. Since only two F-shaped slots are etched on either sides of the radiator for triple-band operation, the radiator is very compact in size and simple in structure. The antenna shows three distinct bands I from 2.0 to 2.76, II from 3.04 to 4.0, and III from 5.2 to 6.0 GHz, which covers entire WLAN (2.4/5.2/5.8 GHz) and WiMAX (2.5/3.5/5.5) bands. To validate the proposed design, an experimental prototype has been fabricated and tested. Thus, the simulation results along with the measurements show that the antenna can simultaneously operate over WLAN (2.4/5.2/5.8 GHz) and WiMAX (2.5/3.5/5.5 GHz) frequency bands.

1 June 2018 in AEU - International Journal of Electronics and Communications
Verified
Journal Article
Closed access
NJNaveen Jaglan
Naveen Jaglan
SGSamir Dev Gupta
Samir Dev Gupta
ETEkta Thakur
Ekta Thakur
DKDinesh Kumar
Dinesh Kumar
BKBinod Kumar Kanaujia
Binod Kumar Kanaujia
SSShweta Srivastava
Shweta Srivastava

30 July 2021 in IEEE Access
Verified
Journal Article
Open access
SKSanjeev Kumar
Sanjeev Kumar
DNDurgesh Nandan
Durgesh Nandan
KSKunal Srivastava
Kunal Srivastava
Sachin KumarSachin Kumar
Sachin Kumar
HSHari Singh
Hari Singh
BKBinod Kumar Kanaujia
Binod Kumar Kanaujia
In this paper, a wideband circularly polarized (CP) textile multiple-input-multiple-output (MIMO) antenna is presented for wearable applications. The designed MIMO antenna consists of two sickle-shaped resonating elements and a common ground plane. Each antenna element is excited by a microstrip line feed, and an inverted L-shaped strip is introduced in the ground plane to support circular polarization. The antenna covers impedance bandwidth ( $\text{S}_{11}\le -10$ dB) of 3.6–13 GHz and 3-dB axial ratio bandwidth (ARBW) of 5.2–7.1 GHz. The proposed textile MIMO antenna exhibits envelope correlation coefficient (ECC) < 0.02, diversity gain (DG) $>9.96$ , total active reflective coefficient (TARC) $ < -10$ dB, channel capacity loss (CCL) < 0.2 b/s/Hz, and mean effective gain (MEG) ratio within ±0.5 dB. The antenna offers dual-sense circular polarization and high isolation (>18) between the resonating elements. Also, the proposed antenna is investigated for different human body situations, and its specific absorption rate (SAR) for human tissues specimen is studied. The overall size of the proposed CP textile MIMO antenna is $32.5 \times 42 \times 1$ mm 3 . The designed MIMO antenna could be useful for wearable applications due to its textile layers, reasonable on-body performance, and compact size.