1 March 2020 in Journal of Transportation Engineering, Part A: Systems
Approximately 47% of fatal crashes in the US and 36% in the European Union occur during the night. Reduced sight distance may contribute to this phenomenon and similar speeds driven between day and night can become problematic along horizontal curves. In this case, drivers are not provided adequate time to adjust their speed for safe negotiation of the curve which can be completed under daylight conditions. This study is the first step toward demonstrating the influence of curvature on nighttime crashes through a preliminary analysis aiming to identify the magnitude of the problem. Data from the US and Greece have been examined and the findings indicate that there is indeed an increased crash occurrence during the night related to the curve radius. Curves with small radii showed an increase in crash occurrence and rate compared to that of corresponding daytime data. The radii of successive curves were utilized as a measure of design consistency and the data again noted differences in crashes between daytime and nighttime conditions.
14 January 2019 in Transportation Research Record: Journal of the Transportation Research Board
ICIoannis-Alexandros Choupas
Ioannis-Alexandros Choupas
Skew superelevation has proven to be an efficient pavement constructional measure to address hydroplaning phenomena under specific critical superelevation runoff designs. However, this technique has raised concerns about user’s comfort when driving over the skewed edge of the pavement, especially for heavy vehicles and when the traveling speed is higher than the design speed. This paper aims to evaluate the driving comfort outcome on an improved skew superelevation design, where a rounding of the skew edge has been applied. This is achieved through the use of a simulation program which examines the vehicle and driver behavior when passing over it. The simulation program estimates many parameters including the lateral and vertical accelerations (Gy and Gz) imposed on both elements, the vehicle and the driver. This evaluation is made for different alignment designs provided in the freeway design and for a broad range of especially high velocities ranging from 80 to 160 km/h (50–100 mph), as well as for different types of heavy vehicles. Also, the influence on the above parameters has been investigated in respect of the distance between two consecutive skew superelevations, concerning cases of entering and exiting a simple, low-length curve. The outcomes are classified in order to evaluate their variability as affected by each parameter change (speed, geometry, vehicle). Simulation results are compared with thresholds, as provided in the international literature, to ensure driver comfort and a high level of road safety.
1 February 2021 in Journal of Transportation Engineering, Part A: Systems
The objective of this paper is the creation of a suitable methodology capable of deploying elements that characterize the existing infrastructure on rural two-lane highways regarding the location and geometric features of intersections and evaluating the built-in road safety. The target is the utilization of these elements to lead to evaluation coefficients that show the hazard level of every intersection and every road section, highlighting the intersections of the road network with reduced safety level. In this context, a hierarchy of critical parameters influencing the risk of an intersection was made, along with appropriate mathematical equations based on the current regulations and corresponding crash reduction factors (CRFs) that have been presented in the literature. Initially, case studies were conducted, and special diagrams were produced to assess the hazard level of each parameter. Then, basic statistical analysis of the results was made using regression factors to develop an appropriate mathematical model for the estimation of the hazard level. A corresponding procedure was performed for each parameter separately, and appropriate coefficients were sought. These coefficients were summed up, and a total score characterizing each intersection has been calculated, leading to a ranking in respect with the hazard level. Finally, data were collected on a significant sample of the existing road network of Greece, about 1,000 km of road network with more than 4,000 intersections (unpaved road intersections are also included), in order to evaluate the results of the proposed methodology. Part of the results has been interpreted with real accident data collected from the police department, showing that there is a correlation between them. This correlation must be confirmed in further research by a statistical analysis between the results of the present methodology and the actual recorded accidents.
7 October 2025 in Transportation Research Record: Journal of the Transportation Research Board
The geometric elements of interchange ramps are selected to provide comfortable and safe passage. In previous studies, field measurements on interchange ramps revealed that the lateral acceleration experienced by drivers was lower than the design value derived from the basic curve equation for a specific radius, superelevation, and speed. This study aims to explain the deviations using the geometric criteria, noting that the discrepancy between the recorded lateral acceleration and the design value is because of the driving (vehicle path) radius and the critical geometric and cross-sectional elements of the horizontal curve (radius, superelevation, deflection angle, curvature change rate, lane width, number of lanes and directions). The sample consists of over 160 drivers with various characteristics (e.g., age group, experience, gender). The measurements were conducted on eight interchange ramp curves. The presented diagrams correlate either the driving or the differential radius with the critical geometric elements of the curves and highlight the significance of each. New equations are established for direct computation of the driving and the differential radius, which can contribute to the selection of the minimum radius values and the speed limit in dry pavement conditions for each new interchange ramp and the differentiation of the current values when incorporated into the design guidelines. The comfort, tolerance, and safety limits of driving and differential radius are established based on design radius, complementing established limits for lateral acceleration and longitudinal deceleration in interchange ramps, to encourage design guidelines to revise the current manuals under the framework of performance-based design.
7 September 2026 in Transportation Research Record: Journal of the Transportation Research Board
This study is an investigation of vehicle passing paths from a road engineering perspective, with an emphasis on the first pair of consecutive reverse-curved sections during the initial phase of the passing maneuver; the aim is to quantify their geometric and dynamic trajectory features. The assessment is based on 233 valid accelerated passing maneuvers obtained from field driving and driving simulator experiments, in which a realistic representation of the passing task was performed. The curved paths were determined for four posted-speed scenarios (70, 80, 90, and 110 km/h), while the impeding vehicle was assumed to travel under steady-state conditions at 20 km/h below the posted speed. In addition to trajectory geometry, the analysis examines critical parameters, such as headway distance, lateral safety margin, and acceleration performance. Two linear regression models were developed to predict the radius of the initial curve ( R 1 ) and the calibrated length of the initial overtaking path segment ( L 1,2cal ), yielding adjusted R 2 values of 0.73 and 0.65, respectively, while model robustness was further examined through sensitivity analysis. The main contribution of the study is the development of a highway engineering–oriented framework for standardizing overtaking trajectories by optimizing deflection angle and acceleration, as well as interpreting steering path data through a vehicle dynamics model. In view of future vehicle automation, the proposed framework may support a more accurate representation and standardization of the passing process, with potential application in roadway design and safety assessment, as well as advanced driver assistance systems.