Mohammad Taherzadeh-Sani

Mohammad Taherzadeh-Sani

Auto-generated profile, based on publicly available information

Mohammad Taherzadeh-Sani

Electrical Engineering Department, Ferdowsi University of Mashhad, Mashhad, Iran

Research Focus & Metrics

Academic Career Length

24Years (2003-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 January 2011 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
MTMohammad Taherzadeh-Sani
Mohammad Taherzadeh-Sani
AHAnas A. Hamoui
Anas A. Hamoui
A pseudo-cascode compensation technique is proposed to enable a process-insensitive and current-scalable design of the classical two-stage opamp at low supply voltages, without requiring any additional power dissipation. Furthermore, a bulk-biasing technique is proposed to enhance the dc gain of the two-stage opamp, without affecting its output-voltage swing and without requiring any additional power dissipation. To compare the performance advantages of the proposed pseudo-cascode compensation technique versus classical Miller compensation in a two-stage opamp with/without applying the proposed bulk-biasing technique, four opamps were fabricated on the same die in a 1-V 65-nm CMOS process. The corresponding transistors in all four opamps had equal sizes. Furthermore, all four opamps had equal total compensation capacitance and the same total power dissipation. Accordingly, compared to using Miller compensation, by applying the proposed pseudo-cascode-compensation and bulk-biasing techniques in a two-stage opamp, the opamp's dc gain is increased by a factor of 4 (12 dB), its unit-gain frequency is increased by 40%, and its phase margin is maintained over a factor of 100 scaling in its bias current. Furthermore, the overshoot in its large-signal step response is eliminated and the rise/fall settling times are improved by 33%. The trade-off is a minimal decrease in the opamp's phase margin. Importantly, this is all achieved without affecting the opamp's output-voltage swing and without requiring any additional power dissipation.

1 February 2017 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
Verified
Journal Article
Closed access
MTMohammad Taherzadeh-Sani
Mohammad Taherzadeh-Sani
SHSaid M. Hussain Hussaini
Said M. Hussain Hussaini
HRHamidreza Rezaee-Dehsorkh
Hamidreza Rezaee-Dehsorkh
FNFrederic Nabki
Frederic Nabki
MSMohamad Sawan
Mohamad Sawan
A fully integrated current sensing interface chip employing a capacitive-feedback transimpedance amplifier (TIA) is presented. A robust dc current removal block is proposed to prevent the dc portion of the input current from saturating the output voltage. This block allows the TIA to operate in the presence of a wide range of input dc currents, and the cancellation loop is designed to enhance its stability. The TIA is fully integrated in a standard 0.13 μm CMOS technology, and a gain of 170 dBΩ is achieved without requiring any off-chip resistors. The integrated input-referred current noise of the interface circuit is 0.4, 3.8, and 52 pARMS within 0.01, 0.1, and 1 MHz integration bandwidths, respectively.

25 September 2006 in IEEE Transactions on Circuits and Systems II: Analog and Digital Signal Processing
Verified
Journal Article
Closed access
MTM. Taherzadeh-Sani
M. Taherzadeh-Sani
AHA.A. Hamoui
A.A. Hamoui
A digital background calibration technique is proposed to correct for the linearity error due to capacitor mismatches in pipelined analog-to-digital converters (ADCs). During the normal ADC operation, it randomly swaps the feedback capacitor with the sampling capacitor(s) in the multiplying digital-to-analog converter (MDAC) of each pipeline stage in the pipelined ADC. The capacitor-mismatch errors in all pipeline stages are then concurrently measured and corrected in the digital domain. The proposed technique can be utilized in both single-bit and multibit MDACs. Owing to its simple iterative algorithm for capacitor-mismatch error calibration, its implementation requires minimal additional digital hardware. Behavioral simulation results show that, using the proposed calibration technique, the signal-to-noise-plus-distortion ratio is improved from 10 to 12.5bits and the spurious-free dynamic range is increased from 65 to 95 dB, in a 13-bit pipelined ADC with sigma=0.25% capacitor mismatches

1 January 2003
Verified
Conference Paper
Closed access
MTM. Taherzadeh-Sani
M. Taherzadeh-Sani
RLR. Lotfi
R. Lotfi
HZH. Zare-Hoseini
H. Zare-Hoseini
OSOmid Shoaei
Omid Shoaei
One of the most important facilities required in the synthesis of an advanced mixed-mode system is the efficient and if possible automated analog design tool. In this paper an accurate method to determine the device sizes in an analog integrated circuit on the basis of genetic algorithm (GA) is presented. In order to evaluate the fitness of the circuit specifications in any iteration of the GA, HSPICE simulation is used. Examples in both time and frequency domains for an operational transconductance amplifier are presented. The simulation results confirm the efficiency of GA in determining the device sizes in an analog circuit.

3 July 2019 in IEEE Transactions on Components, Packaging and Manufacturing Technology
Verified
Journal Article
Closed access
AGAnubha A. Gupta
Anubha A. Gupta
MSMichiel C. M. Soer
Michiel C. M. Soer
MTMohammad Taherzadeh-Sani
Mohammad Taherzadeh-Sani
Sylvain CloutierSylvain Cloutier
Sylvain Cloutier
RIRicardo Izquierdo-Bernier
Ricardo Izquierdo-Bernier
This paper presents a low loss microstrip line, entirely fabricated using aerosol-jet printing (AJP) technology directly to a MMIC chip to achieve high-speed on-chip connectivity. AJP is a direct write fabrication method capable of printing materials with viscosity ranging from 1-1000 cP, with a printing resolution and alignment precision of 10 μm and 2 μm respectively. The length of the printed transmission line is 2 mm and the S-parameters are measured from 500 MHz to 18 GHz. In this paper, the microstrip line is first printed on PCB and the fabrication process is optimized to reach a transmission loss of 0.3 dB/mm at 18 GHz. Subsequently, the microstrip line is printed atop an MMIC architecture to achieve a transmission loss under 0.9 dB/mm at 18 GHz. These results clearly show the potential of using direct printing of microstrip lines as an alternative to conventional wire bonding for wide-bandwidth MMIC electronics packaging applications.

1 November 2003 in Integration
Verified
Journal Article
Closed access
RLReza Lotfi
Reza Lotfi
MTMohammad Taherzadeh-Sani
Mohammad Taherzadeh-Sani
MAM.Yaser Azizi
M.Yaser Azizi
OSOmid Shoaei
Omid Shoaei