Rita Porcaro

Rita Porcaro

Auto-generated profile, based on publicly available information

Rita Porcaro

Department of Civil, Chemical, Environmental and Materials Engineering, University of Bologna, Bologna, Italy

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 May 2024 in Journal of the Mechanical Behavior of Biomedical Materials
Verified
Journal Article
Open access
NENicolas Emiliani
Nicolas Emiliani
RPRita Porcaro
Rita Porcaro
Gregorio PisaneschiGregorio Pisaneschi
Gregorio Pisaneschi
BBBarbara Bortolani
Barbara Bortolani
FFFabrizio Ferretti
Fabrizio Ferretti
Laura CercenelliLaura Cercenelli
Laura Cercenelli
Material Jetting (MJ) 3D printing technology is promising for the fabrication of highly realistic surgical simulators, however, the changes in the mechanical properties of MJ materials after post-printing treatments and over time remain quite unknown. In this study, we investigate the effect of different post-printing processes and aging on the mechanical properties of a white opaque and rigid MJ photopolymer, a white flexible MJ photopolymer and on a combination of them. Tensile and Shore hardness tests were conducted on homogeneous 3D-printed specimens: two different post-printing procedures for support removal (dry and water) and further surface treatment (with glycerol solution) were compared. The specimens were tested within 48 h from printing and after aging (30-180 days) in a controlled environment. All groups of specimens treated with different post-printing processes (dry, water, glycerol) exhibited a statistically significant difference in mechanical properties (i.e. elongation at break, elastic modulus, ultimate tensile strength). Particularly, the treatment with glycerol makes the flexible photopolymer more rigid, but then with aging the initial elongation of the material tends to be restored. For the rigid photopolymer, an increase in deformability was observed as a major effect of aging. The hardness tests on the printed specimens highlighted a significant overestimation of the Shore values declared by the manufacturer. The study findings are useful for guiding the material selection and post-printing processing techniques to manufacture realistic and durable models for surgical training.

25 August 2024 in Progress in Additive Manufacturing
Verified
Journal Article
Open access
PDF file
RPRita Porcaro
Rita Porcaro
FFFrancesco Fontana
Francesco Fontana
MCMichele Ciotti
Michele Ciotti
Mattia MeleMattia Mele
Mattia Mele
Gregorio PisaneschiGregorio Pisaneschi
Gregorio Pisaneschi
MFMAURIZIO FIORINI
MAURIZIO FIORINI
In injection moulding and additive manufacturing processes, it is common for the final product to exhibit warpage induced by a non-uniform cooling rate after material deposition. Residual stresses can be generated in the built parts, with a volume shrinkage that leads to dimensional inaccuracy and reduced usability. This phenomenon is even amplified in the presence of semi-crystalline polymers, which still need to be more widespread among additive manufacturing processes despite their capacity to show better mechanical properties when compared to amorphous ones. This study evaluates the degree of deformation and subsequently characterises the mechanical properties of a novel modified Polyamide 6 formulation (i.e., RADILON® S X21351 NT) printed through the Arburg Plastic Freeforming process. This new proprietary formulation modified the crystallisation behaviour during cooling. The whole exothermic crystallisation peak was shifted to lower temperatures, allowing the processing envelope of the modified formulation to widen. More specifically, after preliminary polymer characterisation analyses and after evaluating the warpage, a mechanical characterisation was performed using tensile tests on specimens (dry-as-moulded and conditioned) printed with different filling strategies on the build platform (XY-0°; XY- ± 45°; XY-90°; ZX-0°). Measured mechanical properties were ultimately compared to those achieved by applying the injection moulding technique on the same non-modified material. The specimens produced through the Arburg Plastic Freeforming process showed brittle behaviour that was more marked than those obtained by injection moulding. Moreover, the infill direction and water content significantly influenced the mechanical properties of specimens.

17 September 2023 in Composites Part A: Applied Science and Manufacturing
Verified
Journal Article
Open access
CLC. Leone
C. Leone
RPR. Porcaro
R. Porcaro
GCG. Campana
G. Campana
SGS. Genna
S. Genna

16 July 2026 in Additive Manufacturing
Verified
Journal Article
Closed access
RPRita Porcaro
Rita Porcaro
APAmy M. Peterson
Amy M. Peterson
GCGiampaolo Campana
Giampaolo Campana
MFMAURIZIO FIORINI
MAURIZIO FIORINI

25 February 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
RPRita Porcaro
Rita Porcaro
APAmy Peterson
Amy Peterson
GCGiampaolo Campana
Giampaolo Campana
MFMAURIZIO FIORINI
MAURIZIO FIORINI
This study investigates the coalescence behavior of bisphenol A polycarbonate droplets in the Arburg Plastic Freeforming additive manufacturing process through a computational framework that integrates thermal, rheological, and mechanical analyses. Using FLOW-3D simulations, the influence of extrusion temperature on droplet morphology, thermal field evolution, and interfacial bonding was examined. The polymer was modelled as a non-Newtonian, shear-thinning fluid with temperature-dependent viscosity, and the bonding potential was quantified using a William-Landel-Ferry (WLF)based equivalent time at the glass transition after contact initiation and a numerically estimated tensile strength. Results reveal that higher extrusion temperatures promote greater spreading and wetting, enlarge the initial contact area, and extend the viscoelastic activation window, thereby improving interfacial coalescence. An equivalent time analysis based on WLF theory and a tensile-strength numerical evaluation reflect a balance between thermal input and spreading-driven post-contact cooling, rather than a purely monotonic temperature effect. These findings provide a predictive framework for optimizing Arburg Plastic Freeforming process parameters to improve part quality and mechanical performance.