Vander Teixeira Prado

Vander Teixeira Prado

Auto-generated profile, based on publicly available information

Vander Teixeira Prado

Faculdade de Engenharia de Ilha Solteira, Universidade Estadual Paulista, SP (15385-000), Brasil

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2013 in NDT & E International
Verified
Journal Article
Closed access
VPVander T. Prado
Vander T. Prado
RHRicardo T. Higuti
Ricardo T. Higuti
CKClaudio Kitano
Claudio Kitano
ÓMÓscar Martinez-Graullera
Óscar Martinez-Graullera
JAJulio C. Adamowski
Julio C. Adamowski

1 November 2017 in Mechanical Systems and Signal Processing
Verified
Journal Article
Closed access
ATAline E. Takiy
Aline E. Takiy
CKCláudio Kitano
Cláudio Kitano
RHRicardo T. Higuti
Ricardo T. Higuti
SGSilvio C.G. Granja
Silvio C.G. Granja
VPVander T. Prado
Vander T. Prado
ÓMÓscar Martinez-Graullera
Óscar Martinez-Graullera

23 June 2014 in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
Verified
Journal Article
Closed access
VPVander Teixeira Prado
Vander Teixeira Prado
RHRicardo Tokio Higuti
Ricardo Tokio Higuti
CKClaudio Kitano
Claudio Kitano
ÓMÓscar Martinez-Graullera
Óscar Martinez-Graullera
A method for reflector detection, based on the instantaneous phase of the aperture data for ultrasonic images, is proposed. The instantaneous phase (IP) image is obtained by replacing the amplitude information by the instantaneous phase in the delay-and-sum (DAS) beamforming. From the analysis of the IP image, a threshold level is defined in terms of the number of signals used for imaging. This threshold is applied to the IP image, resulting in a two-level image which gives a statistical indication of whether the pixels of a region in the image are related to a reflector or noise/artifacts. Because the proposed method uses only the instantaneous phase of the signals, it is less sensitive to attenuation than conventional DAS amplitude images. The point spread function of a 32-element array with half-wavelength pitch at 5 MHz in water is simulated and the reflector is detected for signal-to-noise ratio values larger than -29.6 dB. A phantom and an aluminum plate with artificial defects are tested with the proposed technique, using linear arrays of 64 and 16 elements, respectively. When compared with DAS amplitude images and with two-level images obtained by thresholding the amplitude images using empirical threshold values, the proposed technique reduced artifacts and dead zone, and detected all reflectors, increasing reflectors' detectability and decreasing the occurrence of false indication of reflectors. The proposed technique can be used as additional information for amplitude image analysis, with the advantages that it does not need time-gain compensation and that it considers an objective threshold value.

13 October 2015 in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
Verified
Journal Article
Closed access
VPVander Teixeira Prado
Vander Teixeira Prado
SGSilvio Cesar Garcia Granja
Silvio Cesar Garcia Granja
RHRicardo Tokio Higuti
Ricardo Tokio Higuti
CKClaudio Kitano
Claudio Kitano
ÓMÓscar Martinez-Graullera
Óscar Martinez-Graullera
LSLuis Elvira Segura
Luis Elvira Segura
Anisotropic materials are widely employed in industry and engineering, and efficient nondestructive testing techniques are important to guarantee the structural integrity of the involved parts. A simple technique is proposed to detect defects in anisotropic plates using ultrasonic guided waves and arrays. The technique is based on the application of an objective threshold to a synthetic aperture image obtained from the instantaneous phase (IP) of the emitter-receiver signal combinations. In a previous work the method was evaluated for isotropic materials, and in this paper it is shown that with some considerations the technique can also be applied to anisotropic plates. These considerations, which should be taken into account in beamforming, are (1) group velocity dependence with propagation direction, and (2) elastic focusing, which results in energy concentration in some propagation directions, with the practical consequence that not all aperture signals effectively contribute to the image. When compared with conventional delay-and-sum image beamforming techniques, the proposed IP technique results in significant improvements relative to defect detection and artifacts/dead zone reduction.

19 April 2013 in Journal of Control, Automation and Electrical Systems
Verified
Journal Article
Closed access
PDF file
VPVander Teixeira Prado
Vander Teixeira Prado
RHRicardo Tokio Higuti
Ricardo Tokio Higuti
CKClaudio Kitano
Claudio Kitano
ÓMÓscar Martinez-Graullera
Óscar Martinez-Graullera

1 July 2013
Verified
Conference Paper
Closed access
VPV. T. Prado
V. T. Prado
RHRicardo Tokio Higuti
Ricardo Tokio Higuti
CKClaudio Kitano
Claudio Kitano
ÓMÓscar Martinez-Graullera
Óscar Martinez-Graullera
Sparse arrays have pitch larger than halfwavelength (λ/2) and there is a reduced number of elements in comparison with a full-populated array. Consequently, there is a reduction in cost, data acquisition and processing. However, conventional beamforming techniques result in large side and grating lobes, and consequently in image artifacts. In this work the instantaneous phase of the signals is used in a beamforming technique instead of the instantaneous amplitudes to improve images obtained from sparse arrays configurations. A threshold based on a statistical analysis and the number of signals used for imaging is applied to each pixel, in order to determine if that pixel is related to a defect or not. Three sets of data are used to evaluate the technique, considering medical and non-destructive testing: a simulated point spread function, a medical phantom and an aluminum plate with 2λ-, 7λ- and λ-pitch, respectively. The conventional amplitude image is superposed by the image improved by the instantaneous phase, increasing the reflectors detectability and reducing artifacts for all cases, as well as dead zone for the tested plate.