2 November 2011 in IEEE Transactions on Microwave Theory and Techniques
In this paper, we evaluate the effect of applying peak-to-average power ratio (PAPR) reduction and digital pre-distortion (DPD) on two types of radio frequency power amplifiers when an orthogonal frequency division multiplexing (OFDM) signal is used. The power amplifiers under test are a standard class-AB amplifier and a Doherty amplifier. The PAPR reduction methods are based on a state-of-the art convex optimization formulation and on the standard clipping and filtering technique. The DPD method consists of modeling the behavior of the power amplifier using a parallel Hammerstein model, and then extracting the inverse parameters based on the indirect learning architecture. To achieve better DPD performance, extracting the DPD parameters based on multiple-step iterations is investigated. The cases where PAPR reduction and DPD are applied separately and combined are studied and investigated. Power amplifier figures of merit are evaluated. Good performance is shown when combining both pre-processing techniques up to a certain operating point where DPD performance deteriorates due to generation of strong peaks in the signal. In addition, a difference in the power amplifier behavior is reported and analyzed.
2 November 2021 in IEEE Transactions on Microwave Theory and Techniques
A novel behavioral modeling technique for digital predistortion of radio frequency power amplifiers (PAs) is proposed. The proposed basis-propagating selection (BAPS) model has an advantage on complexity since its basis functions are constructed as delay or a combination of existing basis functions. The BAPS model effectively optimizes the running time complexity while maintaining the generality of a full Volterra series. A greedy search procedure is applied to select the optimal basis functions. Compared with truncated Volterra models and pruned models obtained by popular pruning techniques, the superior performance of the BAPS model, in terms of accuracy and identification stability, has been fairly justified. The linearization measurements on different types of PAs illustrate that the BAPS model can robustly outperform other models from literature while achieving a low running complexity.
27 February 2012 in IEEE Transactions on Microwave Theory and Techniques
This paper presents a direct model structure for describing class-D outphasing power amplifiers (PAs) and a method for digitally predistorting these amplifiers. The direct model structure is based on modeling differences in gain and delay, nonlinear interactions between the two paths, and differences in the amplifier behavior. The digital predistortion method is designed to operate only on the input signals' phases, to correct for both amplitude and phase mismatches. This eliminates the need for additional voltage supplies to compensate for gain mismatch. Model and predistortion performance are evaluated on a 32-dBm peak-output-power class-D outphasing PA in CMOS with on-chip transformers. The excitation signal is a 5-MHz downlink WCDMA signal with peak-to-average power ratio of 9.5 dB. Using the proposed digital predistorter, the 5-MHz adjacent channel leakage power ratio (ACLR) was improved by 13.5 dB, from -32.1 to -45.6 dBc. The 10-MHz ACLR was improved by 6.4 dB, from -44.3 to -50.7 dBc, making the amplifier pass the 3GPP ACLR requirements.
14 September 2012 in IEEE Transactions on Microwave Theory and Techniques
This paper investigates the issue of “predistorter blow-up,” i.e., uncontrolled peak expansion caused by the predistorter. To control the peak expansion, an extension of the multistep indirect learning architecture (MS-ILA) is proposed by adding a constraint that describes the allowed peak power of the predistortion signal. The resulting optimization problem is shown to be convex and an optimization method is formulated to solve it. Measurements on a class-AB power amplifier (PA) using orthogonal frequency-division multiplex signals show that the peak control works as intended and prevents the MS-ILA from generating high peaks when the PA is operated in compression. The restriction on the peak power also prevents the performance degradation occurring due to the “blow-up” problem. This makes the proposed controlled MS-ILA a safer option than the standard MS-ILA. In addition to controlling the peak input power to the PA, using the proposed method it was possible to increase the output power by 1.3 dB while fulfilling requirements of less than 40-dB adjacent channel leakage power ratio, compared to the standard five-step MS-ILA. Reduced peak power also reduces the requirements on linearity in signal generation, resolution in computations, and analog-to-digital and digital-to-analog conversion.
2 April 2014 in International Journal of Microwave and Wireless Technologies
Two novel memory polynomial models are derived based on physical knowledge of a general power amplifier (PA). The derivations are given in detail to facilitate derivations of other model structures. The model error in terms of normalized mean square error (NMSE) and adjacent channel error power ratio (ACEPR) of the novel model structures are compared to that of established models based on the number of parameters using data measured on two different amplifiers, one high-power base-station PA and one low-power general purpose amplifier. The novel models show both lower NMSE and ACEPR for any chosen number of parameters compared to the established models. The low model errors make the novel models suitable candidates for both modeling and digital predistortion.
6 January 2010 in International Journal of RF and Microwave Computer-Aided Engineering
A frequency-weighted parameter extraction method based on the performance evaluation criterion weighted error spectral power ratio is proposed. Performance of models extracted using the normalized mean square error are compared to the performances of models extracted using the WESPR. The results show an increase in performance with a decrease in model complexity. © 2010 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2010.