24 June 2022 in IEEE Transactions on Electron Devices
This article presents a bulk acoustic wave (BAW) resonator with complementary switchable operation in the first and second thickness extensional modes (TE 1 and TE 2 ) at 7.04 and 13.4 GHz. Two ferroelectric scandium aluminum nitride (Sc 0.28 Al 0.72 N) layers are alternatively stacked with three molybdenum electrodes, creating a laminated BAW resonator with independent switchability of polarization in constituent transducers. This enables intrinsic switchability of the resonator in TE 1 and TE 2 modes, when the ferroelectric Sc 0.28 Al 0.72 N layers are poled in the same or opposite directions, respectively. A generalized analytical proof of complementary switchable operation, extended to laminated BAW resonators consisting of arbitrary number of Sc x Al 1-x N layers, is presented. For the demonstrated prototype, electromechanical coupling coefficients ( ${k}_{t}^{2}$ ) of 10.1% and 10.7%, and quality factors ( ${Q}$ ) of 115 and 151, are measured for TE 1 and TE 2 modes, respectively, when the resonator is configured in the corresponding operation states. Besides showing intrinsically configurable operation in super-high-frequency regime with high ${k}_{t}^{\textbf {2}}$ and ${Q}$ , a laminated Sc 0.28 Al 0.72 N BAW resonator exhibits repeatable operation under switching cycles.
10 May 2021 in IEEE Electron Device Letters
This letter reports intrinsically switchable ultra- and super-high-frequency Lamb-mode resonators based on the use of ferroelectricity in scandium aluminum nitride (Sc x Al 1-x N) films. Highly crystalline 200nm-thick Sc 0.22 Al 0.78 N film is sputtered using segmented-target reactive magnetron sputtering, and interdigitated electrodes are patterned to create one-port resonators operating in symmetric Lamb modes. The resonators are intrinsically switched using the ferroelectric behavior in Sc 0.22 Al 0.78 N film and through polarization switching at one of the terminals, resulting in a zero-sum electromechanical coupling factor ( k t 2 ). Resonators with frequencies over 0.45 - 6 GHz, frequency × quality factor product ( f s ×Q) as high as 4×10 12 , and and k t 2 ×Q product exceeding29 aredemonstrated. The intrinsic switchability of resonators is characterized using 100ms triangular monopolar pulses, resulting in an admittance switching isolation as high as 15dB.
17 August 2022 in Physica Status Solidi (RRL) – Rapid Research Letters
1 March 2025 in Applied Physics Letters
We demonstrate a temperature-stable oscillator based on frequency Duffing in a degenerately doped silicon bulk acoustic wave resonator, transduced by a thin aluminum scandium nitride (AlScN) layer. The resonator operates in the cross-sectional Lamé (X-Lamé) mode at 64.7 MHz, exhibiting an ultra-high quality factor (Q) of 110 000 and a first-order temperature coefficient of frequency (TCF1) compensation. Additionally, the resonator provides amplitude-dependent frequency tunability through elastic Duffing. A secondary cross-sectional square-extensional (X-SE) mode at 92 MHz, with high linear temperature sensitivity, enables in situ temperature sensing. An oscillator is constructed with autonomous loop-gain control, leveraging the X-SE mode to compensate for the second-order TCF(TCF2) of the X-Lamé mode through nonlinear Duffing. This results in a frequency reference with a third-order temperature characteristic, featuring an insensitive region around the inflection points, with a TCF3 of 7 ppb/°C3. An overall frequency drift of ±1.88 ppb is measured for this weakly nonlinear oscillator over 1.47 °C temperature range near the 56 °C inflection point, showing an order of magnitude reduction in instability compared to the linear operation mode.
4 August 2025 in IEEE Transactions on Circuits and Systems I: Regular Papers
A major challenge of long-term clock stability is frequency drift due to temperature variations. This paper describes the design of a proportional, integral, derivative (PID) control system for external ovenization of an AlScN-on-Si Shear-BAW Resonator (S3R), which has a fixed turnover temperature where the $1{^{\text {st}}}$ order temperature coefficient of frequency is $\approx 0$ ppm/°C. The control system provides $\pm ~0.125^{\circ }$ C temperature stability and assists in achieving better than $\pm ~25$ ppb frequency stability over a temperature range of 15-40°C by maintaining resonator operation near the turnover temperature, where the $2{^{\text {nd}}}$ order temperature coefficient of frequency drift is -62.71ppb/°C2. The robust and adaptive PID algorithm (programmed on an external microcontroller unit connected to the interposer) ensures continuous ovenization by configuring the duty cycle of a compact heat actuator (powerMOS) that is placed in <3.5mm proximity of the 2mm $\times 2$ mm resonator and a complementary to absolute temperature sensor (implemented as a 1mm $\times 1$ mm, 65nm integrated circuit), that are all held on a thermally conductive 7mm $\times$ 7mm Si interposer.