Yoonho Kim

Yoonho Kim

Auto-generated profile, based on publicly available information

Yoonho Kim

Department of Manufacturing System Design Engineering, Seoul National University of Science and Technology, Seoul, South Korea

Research Focus & Metrics

Academic Career Length

29Years (1998-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 March 2021 in IEEE Transactions on Components, Packaging and Manufacturing Technology
Verified
Journal Article
Closed access
HPHaesung Park
Haesung Park
HSHankyeol Seo
Hankyeol Seo
YKYoonho Kim
Yoonho Kim
SPSeungmin Park
Seungmin Park
Sarah Eunkyung KimSarah Eunkyung Kim
Sarah Eunkyung Kim
Low-temperature solderless Cu-Cu bonding is an important technology for advanced packaging, such as fine-pitch 3-D packaging and heterogeneous integration. In this study, we prepared an oxidation-free Cu surface using an optimized N 2 plasma process in a two-step Ar/N 2 plasma treatment based on the design of the experiment method, to improve direct Cu-Cu bonding quality at 260 °C. The N 2 plasma treatment process was optimized using the Minitab optimizer with chemical state results obtained by X-ray photoelectron spectroscopy (XPS) analysis. The Cu surface treated under the two-step Ar/N 2 plasma with optimized N 2 plasma conditions not only formed Cu nitride well, but the surface remained without further oxidation for at least one week at room temperature. The Cu-Cu bonding was performed at the low bonding temperature of 260 °C and low bonding pressure of 0.9 MPa for 1 hour, and the bonded interface was evaluated using scanning acoustic tomography (SAT) and field emission scanning electron microscope (FE-SEM) images. We measured shear strength to estimate the bonding interface quality of the oxidation-free Cu-Cu bonding specimen. A maximum shear strength of 62.6 MPa was obtained. Our bonding results demonstrated remarkably improved Cu-Cu bonding quality compared with other previous Cu-Cu joint studies that used Sn, Cu/Ag nanoparticles, or Cu composites.

12 October 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
YKYoonho Kim
Yoonho Kim
SPSeungmin Park
Seungmin Park
Sarah Eunkyung KimSarah Eunkyung Kim
Sarah Eunkyung Kim
Low-temperature Cu-Cu bonding technology plays a key role in high-density and high-performance 3D interconnects. Despite the advantages of good electrical and thermal conductivity and the potential for fine pitch patterns, Cu bonding is vulnerable to oxidation and the high temperature of the bonding process. In this study, chip-level Cu bonding using an Ag nanofilm at 150 °C and 180 °C was studied in air, and the effect of the Ag nanofilm was investigated. A 15-nm Ag nanofilm prevented Cu oxidation prior to the Cu bonding process in air. In the bonding process, Cu diffused rapidly to the bonding interface and pure Cu-Cu bonding occurred. However, some Ag was observed at the bonding interface due to the short bonding time of 30 min in the absence of annealing. The shear strength of the Cu/Ag-Ag/Cu bonding interface was measured to be about 23.27 MPa, with some Ag remaining at the interface. This study demonstrated the good bonding quality of Cu bonding using an Ag nanofilm at 150 °C.

19 May 2023 in IEEE Transactions on Components, Packaging and Manufacturing Technology
Verified
Journal Article
Closed access
YKYoonho Kim
Yoonho Kim
Sarah Eunkyung KimSarah Eunkyung Kim
Sarah Eunkyung Kim
One of the key requirements for mass production of die-to-wafer Cu bonding is preventing copper surface oxidation. In this study, Cu bonding utilizing an Ag nanolayer was examined to achieve both Cu surface oxidation prevention and low-temperature bonding. The primary focus was to evaluate the impact of the annealing process on the Cu bonding quality. The Cu surface was coated with a 15 nm thick layer of Ag using evaporation technique. Cu wafer-to-wafer bonding was performed at a temperature of 180°C for 30 min, followed by annealing at 200°C for 60 min. The annealing process resulted in complete diffusion of Cu into the bonding interface, leading to a uniform and pure Cu-to-Cu bonding. However, the Ag nanolayer did not completely dissolve into the Cu thin film and formed a thin Ag band. The average shear strength of the specimens subjected to the annealing process was ~6.5 MPa., which was relatively low. Nonetheless, the annealing process has proven to be a very effective way to create a homogeneous bonding interface and achieve pure Cu-Cu bonding when using Ag nanolayers in Cu bonding.

1 January 1998 in MRS Proceedings
Verified
Journal Article
Closed access
PDF file
SKS.-H. Kim
S.-H. Kim
HSH.-W. Seon
H.-W. Seon
YKYoonho Kim
Yoonho Kim