17 January 2020 in Journal of Applied Physics
The uni-traveling-carrier photodiode (UTC-PD) is a kind of pin junction photodiode that selectively uses electrons as active carriers. The diode structure has a relatively thin p-type absorber where electrons are generated as minority carriers, and then they diffuse and/or field-accelerate toward the collector. Since the electrons travel in the depleted collector at a ballistically high velocity, the photoresponse performance of a UTC-PD is superior to that of a conventional pin-PD. In this tutorial, the basics of the current response in a UTC-PD, the electron transport in the p-type absorber, and the performance of a terahertz-wave UTC photomixer, as a representative, are described.
2 December 2016 in Japanese Journal of Applied Physics
An InP/InGaAs heterobarrier rectifier called a Fermi-level managed barrier (FMB) diode was developed for attaining broadband and low-noise terahertz (THz) wave detection. The barrier height was controlled by doping in an InGaAs layer, achieving a very small barrier-height of 70 meV. The intrinsic zero-biased differential resistance obtained was 110 Ω for an FMB diode with a 0.4 µm 2 junction area. The fabricated device assembled in a quasi-optical module detected THz-wave signals at frequencies from 200 GHz to 1 THz at room temperature. The peak current and voltage sensitivities were respectively 3.7 A/W and 1110 V/W at 300 GHz for a zero-biased condition. An FMB diode module with an integrated preamplifier was also developed for characterizing its performance in practical use. Signal detection at frequencies from 160 GHz to 1.4 THz was attained with a high sensitivity of 3.2 MV/W and a low noise-equivalent power of 3.0 pW/ at 300 GHz.
27 October 2021 in IEEE Journal of Selected Topics in Quantum Electronics
The development of uni-traveling carrier photodiodes over the past 25 years is briefly reviewed and the key design parameters in their structure are discussed. Monte Carlo simulation run for minority electrons in a p-type InGaAs structure reveals how they leave the absorber. This shows the very diffusive nature of electrons, even in a moderately high quasi-field. Output linearity is carefully verified based on experimental THz-wave output vs. operation current. The first stage of saturation prior to severe field collapse is shown to be ruled by space charge density linearly changing with operation current. In the scaling down of a UTC-PD for faster operations, the space-charge effect is not significant, but junction self-heating is a factor imposing limitations.
6 July 2020 in IEEE Photonics Technology Letters
We developed a thermo-optic effect based silica optical phased array (OPA) chip and evaluated its tunability of phases of lightwaves. The THz waves, whose phases are controlled by the OPA chip, are generated from four arrayed uni-travelling-carrier photodiodes (UTC-PDs) based on heterodyne photomixng. Meanwhile, the UTC-PDs, which integrated with $4\times 4$ slot antennas, are fabricated on a monolithic InP substrate chip for 300-GHz wave beam combining and steering. Through the optoelectronic THz-wave phase control, the feasibility of 300-GHz beam continuous steering is successfully demonstrated in a range of 50°.
1 September 2018 in Electronics Letters
A Fermi‐level managed barrier (FMB) diode was used for the heterodyne detection of terahertz waves for the first time. A quasi‐optical module integrating an FMB diode and a broadband trans‐impedance amplifier exhibited an intermediate frequency bandwidth of 11 GHz. A very low noise‐equivalent‐power of 1.1 × 10 −18 W/Hz was achieved at ∼300 GHz with a very low local oscillator power of 6 × 10 −6 W.
25 July 2022 in Journal of Lightwave Technology
Three-dimensional (3D) imaging remains an expensive and challenging task in the THz band. In this study, a frequency-modulated continuous-wave photonic radar system was presented in the 300-GHz band, instead of using electronic-based devices. The proposed system can obtain a 6-dB bandwidth of 120 GHz to achieve a range resolution of ∼1.1 mm. The frequency sweep linearity of a laser source was calibrated with respect to the imaging distance and range resolution, through which a maximum detectable distance of ∼800 mm was achieved with the collimated beam. To obtain the desired 3D information, the synthetic aperture radar (SAR) technique was introduced to the proposed system to achieve 3D imaging, which was not bounded by the fixed focal distance of a focus lens. It can provide a spatial resolution of ∼1.5 mm within a 3D imaging range up to ∼300 mm. The potential and limitations of SAR imaging schemes are discussed based on the theoretical and experimental results.