Bilal Dogan

Bilal Dogan

Auto-generated profile, based on publicly available information

Bilal Dogan

Institute of Graduate Education, Kutahya Dumlupinar University, Kutahya, Turkey

Research Focus & Metrics

Academic Career Length

34Years (1993-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 1996 in Intermetallics
Verified
Journal Article
Closed access
BDB. Dogan
B. Dogan
DSD. Schöneich
D. Schöneich
KSK.-H. Schwalbe
K.-H. Schwalbe
RWRichard Wagner
Richard Wagner

11 August 2010 in International Journal of Pressure Vessels and Piping
Verified
Journal Article
Closed access
BDBilal Dogan
Bilal Dogan

1 October 1993 in Scripta Metallurgica et Materialia
Verified
Journal Article
Closed access
BDB Dogan
B Dogan
GWG.X Wang
G.X Wang
MDM Dahms
M Dahms

1 January 2007
Verified
Conference Paper
Closed access
PDF file
BDBilal Dogan
Bilal Dogan
The effect of weldments in service performance of high temperature components has been subject to intensive research due to the fact that in the majority of cases where high temperature failure occurs, defects predominate in the vicinity of weldments. Cracking occurs in service due to reduced creep ductility of HAZ and weld metal due to ageing in service, combined with the action of multi-axial stress fields that reduce the creep ductility further. The defects detected or assumed to exist through minimum allowable limits of detectable flaws using non-destructive testing methods is required for structural integrity and residual life assessment of high temperature components. The assessment relies on information obtained from the material’s high temperature tensile, uniaxial creep, crack initiation and growth properties. The concepts used for time dependent fracture analysis of homogeneous bodies are commonly applied for creep crack growth in weldments that show multi-crack initiation and crack branching. This calls for study of deformation behavior and applicability of fracture mechanics parameters for high temperature assessment of weldments. The present paper reports on the material behavior and methodology followed for testing and assessment of the high temperature steel weldments.

30 August 2021 in Wood Material Science & Engineering
Verified
Journal Article
Closed access
BDBilal Dogan
Bilal Dogan
OPOsman Percin
Osman Percin
SSSait Dundar Sofuoglu
Sait Dundar Sofuoglu
This study aims to study the improvement in the properties of heat-treated wood material by impregnation. For this purpose, black pine (Pinus nigra Arnold) wood specimens were modified in two stages: impregnation with 1%, 3% and 5% of diammonium phosphate (DAP) and sodium carbonate (SC) compounds followed by heat treatment at four different temperatures. Test specimens were pre-treated with solutions of different pH values of either DAP or SC solutions according to the immersion method and they were exposed to heat treatments at 150°C, 170°C, 190°C and 210°C for 3 h. Some physical and mechanical properties were determined in combined treated specimens with air-dried density, compression strength parallel to grain (CS) and bending strength (MOR). The test results indicated that, as regards the effect of the heat treatment, the mechanical strength decreased due to the increase in temperature, while the losses in the CS were fewer than those of the MOR. In addition, generally combined treatments increased the mechanical properties of the specimens, especially at lower and moderate heat treatment temperatures. Moreover, the SC compound showed more favorable results against the reducing effect of the heat treatment on mechanical strengths.

16 December 2025 in Mobilya ve Ahşap Malzeme Araştırmaları Dergisi
Verified
Journal Article
Closed access
BDBilal Doğan
Bilal Doğan
OPOsman Perçin
Osman Perçin
Bu çalışmada, bor bileşikleri ile emprenye işleminden sonra farklı sıcaklıklarda uygulanan ısıl işlemin ahşap malzemenin fiziksel ve mekanik özellikleri üzerindeki etkisi incelenmiştir. Bu amaçla, deney örnekleri %1, %3 ve %5 konsantrasyonlarında boraks (Bx) ve borik asit (Ba) çözeltileriyle 48 saat daldırma yöntemiyle emprenye edilmiş ve ardından 150°C, 170°C, 190°C ve 210°C'de üç saat ısıl işlem uygulanmıştır. Deney örneklerinin hava kurusu yoğunluk, liflere paralel basınç direnci (BD) ve eğilme direnci (ED) değerleri belirlenmiştir. Araştırma sonuçları, ısıl işlem uygulanmış deney örneklerinde yoğunluk değerlerinin, artan ısıl işlem sıcaklığıyla azaldığını göstermiştir. Öte yandan, bor bileşikleri ısıl işlem uygulanmamış deney örneklerinin yoğunluk değerlerini artırmıştır. Bor bileşikleri ile emprenye işlemi ve ısıl işlem uygulaması deney örneklerinin BD özelliklerinde hafif bir artışa neden olmuştur. Ayrıca, emprenye edilmiş ve ısıl işlem uygulanmış deney örneklerinin ED değerleri, düşük sıcaklıklarda arttığı, yüksek sıcaklıklarda ise azaldığı tespit edilmiştir. Isıl işlem sırasında ED ve BD özelliklerinde görülen azalmaların, ısıl işlemden önce bor bileşikleri ile emprenye edilmesiyle hafifletildiği ve Bx ve Ba emprenye çözeltilerinin sırasıyla BD ve ED özellikleri üzerinde daha olumlu etkilere sahip olduğu belirlenmiştir.