1 November 2018 in Energy Reports
11 May 2020 in Journal of Dynamic Systems, Measurement, and Control
In first stage, a machine learning (ML) was performed to predict in-cylinder pressure using both Fuzzy Logic (FL) and Artificial Neural Networks (ANN) depending on results of experimental studies in a spark ignition (SI) engine. In the ML phase, the experimental in-cylinder pressure data of SI engine was used. SI engine was operated at stoichiometric air-fuel mixture (φ=1.0) at 1200, 1400 and 1600 rpm engine speeds. Six different ignition timings, ranging from 15 to 45 °CA, were used for each engine speed. Correlations (R2) between data from in-cylinder pressure obtained via FL & ANN models and data form experimental in-cylinder pressure were determined. R2 values over 0.995 were obtained at ML stage of ANN model for all test conditions of the engine. However, R2 values were remained between range of 0.820-0.949 with the FL model for different engine speeds and ignition timings. In second stage, in-cylinder pressure prediction was performed by using an ANN model for engine operating conditions where no experimental results were obtained. Furthermore, indicated mean effective pressure (IMEP) values were calculated by predicting in-cylinder pressure data for different engine operation conditions, and then compared with experimental IMEP values. The results show that the in-cylinder pressure and IMEP results estimated with the trained ANN model are fairly close to the experimental results. Moreover, it was found that using the trained ANN model, the ignition timing corresponding to the maximum brake torque (MBT) used in the engine management systems and engine studies could be determined with high accuracy.
17 June 2021 in Sustainable Energy Technologies and Assessments
30 December 2021 in International Journal of 3D Printing Technologies and Digital Industry
Bu çalışmada 3B baskı teknolojisi kullanılarak otonom sualtı aracı (AUV) tasarımı ve uygulamasını gerçekleştirilmiştir. Dünyanın büyük bir bölümü denizler ve okyanuslardan oluşmaktadır. Bu gerçeğe rağmen sualtı araştırmaları kara ve hava ile karşılaştırıldığında geriden gelmektedir. Fakat son yıllarda dünyamızda ve ülkemizde sualtı araştırmaları önem kazanmaktadır. Özellikle sualtı maden, petrol ve doğalgaz yataklarına olan ilgiyle bu alandaki eksik daha çok hissedilmekte ve teknolojik çalışmalara ilgi daha da artmaktadır. Bu noktada en önemli ve en fazla ilgiyi sualtı robotları almaktadır. Yapılan bu çalışmada tüm bu ilgi ve ihtiyaç gereksinimleri ışığında, ilgili her alanda kullanılabilecek bir AUV prototipi gerçekleştirilmiştir. İmalatı gerçekleştirilen otonom sualtı aracı, hidrodinamik, sualtı sabit basınç ve dinamik basınç değişkenleri açısından değerlendirilerek kabiliyet yetenekleri arttırılırmıştır. Otonom sualtı robotunun kabuk tasarımı sualtında manevra yeteneği yüksek canlılar gözlemlenerek gerçekleştirilmiş ve HAD (Hesaplamalı Akışkanlar Dinamiği) analizleri yapılmıştır. Kabuk tasarımı ve imalatının gerçekleştirilmesinin ardından, tahrik sistemi ve elektronik donanımlar tamamlanarak otonom sualtı aracının fiziki yapısı tamamlanmıştır.
19 December 2014 in Celal Bayar Üniversitesi Fen Bilimleri Dergisi
EĞİTİM AMAÇLI ARM TEST SİSTEMİ TASARIM VE İMALATI Yapılan çalışmada 6/4 Anahtarlı Relüktans Motor (ARM) imalat aşamaları (tasarım, analiz, saçların kesimi ve yalıtılması, mekanik gövdenin hazırlanması ve sürücü kısım) tanıtılmıştır. Böylece ARM ile ilgili alanlarda çalışmayı hedefleyen araştırmacıların yaşadığı tedarik sorununun özel imalat ile aşılabilmesi sağlanacaktır. Yapılan çalışmanın temel hedefi ARM ile ilgili eğitim amaçlı deneysel düzeneğin geliştirilmesidir. Ayrıca ARM imalatı esnasında elde edilen bilgi birikiminin "Know-How" paylaşılmasıdır.ARM TEST SYSTEM DESIGN AND MANUFACTURING FOR THE AIM OF EDUCATIONWithin the study carried out, manufacturing steps of 6/4 Switched Reluctance Motor (SRM) (design, analysis, isolating and cutting process of hair, mechanical body preparation and the drive portion) are introduced. Thus, the supply problems for researchers who aim to work in areas related to SRM will be overcome with the custom manufacturing solution. The main objective of the study is to develop experimental setup for training on SRM. In addition, the knowledge obtained during the manufacture of SRM "Know-How" will be shared.
30 April 2019 in Balkan Journal of Electrical and Computer Engineering
In parallel with the increased production of electric vehicles, the research on electric motors has become very popular. Switched Reluctance Machines (SRMs) have been widely preferred in these investigations. Mutually Coupled Switched Reluctance Machine (MCSRM) has higher torque performances than conventional SRMs have. In this study, it is aimed to reduce the weight of MCSRM by geometric arrangement. For this purpose, the MCSRM’s stator yoke is minimized without deteriorating the flux distribution. Various geometrical changes are performed on the stator yoke of the MCSRM. Each of the obtained motor models is magnetostatic analyzed in different currents by finite-element analysis. From comparison of the results of the analysis, it is seen that the proposed MCSRM models show reduction in the stator volumes between 11.31% and 14.17%. This reduction leads to a reduction in the overall weight of the MCSRM.