Yi Zhang

Yi Zhang

Auto-generated profile, based on publicly available information

Yi Zhang

Nankai University

Research Focus & Metrics

Academic Career Length

30Years (1997-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 February 2012 in Journal of Materials Chemistry
Verified
Journal Article
Closed access
PDF file
LWLi Wu
Li Wu
YZYi Zhang
Yi Zhang
MGMingyuan Gui
Mingyuan Gui
PLPengzhi Lu
Pengzhi Lu
LZLixia Zhao
Lixia Zhao
JXJingjun Xu
Jingjun Xu
A series of Dy3+-, Tm3+-, Eu3+-coactivated KSr4(BO3)3 phosphors were synthesized via a standard solid-state reaction under normal ambient air, and the emission colors could be tuned from blue to yellow and then to red, including almost all the white light region, through tuning the energy transfer. It was discovered that the energy is transferred from Tm3+ to Dy3+ by: directly observing overlap of the excitation spectrum of Dy3+ and the emission spectrum of Tm3+; the systematic relative decline and growth of emission bands of Tm3+ and Dy3+, respectively; and faster decay times of the blue emissions from energy donors. The resonance-type energy transfer from Tm3+ to Dy3+ was demonstrated to be via the dipole–quadrupole mechanism and the critical distance of energy transfer was calculated to be 20.7 Å. Rietveld refinements of the crystal structures of the products obtained from powder X-ray diffraction (XRD) elucidated a preferable occupancy in the crystal unit for the doped rare-earth cations, which well explained the formation of the Tm3+–Dy3+ close pair. By utilizing the principle of energy transfer, we have demonstrated that with appropriate tuning of activator content, KSr4(BO3)3:Dy3+,Tm3+,Eu3+ phosphors exhibit great potential for use as single-component phosphors for warm white ultraviolet light-emitting diodes (UV LEDs).

29 January 2018 in Advanced Science
Verified
Journal Article
Open access
PDF file
JLJianjun Li
Jianjun Li
DWDongxiao Wang
Dongxiao Wang
XLXiuling Li
Xiuling Li
YZYu Zeng
Yu Zeng
YZYi Zhang
Yi Zhang
As a promising candidate for low‐cost and environmentally friendly thin‐film photovoltaics, the emerging kesterite‐based Cu2ZnSn(S,Se)4 (CZTSSe) solar cells have experienced rapid advances over the past decade. However, the record efficiency of CZTSSe solar cells (12.6%) is still significantly lower than those of its predecessors Cu(In,Ga)Se2 (CIGS) and CdTe thin‐film solar cells. This record has remained for several years. The main obstacle for this stagnation is unanimously attributed to the large open‐circuit voltage (VOC) deficit. In addition to cation disordering and the associated band tailing, unpassivated interface defects and undesirable energy band alignment are two other culprits that account for the large VOC deficit in kesterite solar cells. To capture the great potential of kesterite solar cells as prospective earth‐abundant photovoltaic technology, current research focuses on cation substitution for CZTSSe‐based materials. The aim here is to examine recent efforts to overcome the VOC limit of kesterite solar cells by cation substitution and to further illuminate several emerging prospective strategies, including: i) suppressing the cation disordering by distant isoelectronic cation substitution, ii) optimizing the junction band alignment and constructing a graded bandgap in absorber, and iii) engineering the interface defects and enhancing the junction band bending.

1 May 2016 in Solar Energy Materials and Solar Cells
Verified
Journal Article
Closed access
JLJianjun Li
Jianjun Li
Hongxia WangHongxia Wang
Hongxia Wang
MLMiao Luo
Miao Luo
JTJiang Tang
Jiang Tang
CCCheng Chen
Cheng Chen
YZYi Zhang
Yi Zhang

1 January 2017 in Solar Energy Materials and Solar Cells
Verified
Journal Article
Closed access
JLJianjun Li
Jianjun Li
SKSeongYeon Kim
SeongYeon Kim
DNDahyun Nam
Dahyun Nam
XLXiaoru Liu
Xiaoru Liu
JKJunHo Kim
JunHo Kim
YZYi Zhang
Yi Zhang

3 February 2015 in Advanced Energy Materials
Verified
Journal Article
Closed access
PDF file
JLJianjun Li
Jianjun Li
YZYi Zhang
Yi Zhang
WZWei Zhao
Wei Zhao
DNDahyun Nam
Dahyun Nam
HCHyeonsik Cheong
Hyeonsik Cheong
YSYun Sun
Yun Sun

14 December 2021 in Energy & Environmental Science
Verified
Journal Article
Closed access
PDF file
HGHongling Guo
Hongling Guo
RMRutao Meng
Rutao Meng
GWGang Wang
Gang Wang
SWShenghao Wang
Shenghao Wang
LWLi Wu
Li Wu
YZYi Zhang
Yi Zhang
Fabrication of highly efficient solar cells is critical for photovoltaic applications. A bandgap-graded absorber layer can not only drive efficient carrier collection but also improve the light harvesting. However, it is very difficult to realize such a bandgap-graded structure in kesterite-structured films due to the similar cation diffusion rates in the high-temperature selenization process. Here, we design and successfully realize a bandgap grade in Cu2ZnSn(S,Se)4 (CZTSSe) film by sufficient annealing during the deposition of an Al-doped ZnO film. This annealing strategy facilitates the solid-state ion-exchange reaction between Cu+ and Cd2+ at the heterojunction interface. Consequently, n-type CdS is partially converted to p-type Cu2S and CZTSSe is converted to Cd-graded CZTSSe, thereby forming a desired bandgap-graded CZTSSe solar cell. The tailored band alignment between the p–n junction not only improves the electron transport but also reduces the carriers recombination. As a consequence, the open-circuit voltage and fill factor are significantly improved, and a certified power conversion efficiency of 12.25% is obtained. The graded bandgap engineering of the absorber achieved here illuminates the future pathway towards highly efficient solar cells.