19 August 2020 in Classical and Quantum Gravity
The TianQin-1 satellite (TQ-1), which is the first technology demonstration satellite for the TianQin project, was launched on 20 December 2019. The first round of experiment had been carried out from 21 December 2019 until 1 April 2020. The residual acceleration of the satellite is found to be about 1 × 10 −10 m/s 2 /Hz 1/2 at 0.1 Hz and about 5 × 10 −11 m/s 2 /Hz 1/2 at 0.05 Hz, measured by an inertial sensor with a sensitivity of 5 × 10 −12 m/s 2 /Hz 1/2 at 0.1 Hz. The micro-Newton thrusters has demonstrated a thrust resolution of 0.1 μ N and a thrust noise of 0.3 μ N/Hz 1/2 at 0.1 Hz. The residual noise of the satellite with drag-free control is 3 × 10 −9 m/s 2 /Hz 1/2 at 0.1 Hz. The noise level of the optical readout system is about 30 pm/Hz 1/2 at 0.1 Hz. The temperature stability at temperature monitoring position is controlled to be about ±3 mK per orbit, and the mismatch between the center-of-mass of the satellite and that of the test mass is measured with a precision of better than 0.1 mm.
19 August 2025 in Classical and Quantum Gravity
TianQin is a future space-based gravitational wave (GW) observatory targeting the frequency window of 10−4–1 Hz. A large variety of GW sources are expected in this frequency band, including the merger of massive black hole binaries, the inspiral of extreme/intermediate mass ratio systems, stellar-mass black hole binaries, Galactic compact binaries, and so on. TianQin will consist of three Earth orbiting satellites on nearly identical orbits with orbital radii of about 105 km. The satellites will form a normal triangle constellation whose plane is nearly perpendicular to the ecliptic plane. The TianQin project has been progressing smoothly following the ‘0123’ technology roadmap. In step ‘0’, the TianQin laser ranging station has been constructed and it has successfully ranged to all the five retro-reflectors on the Moon. In step ‘1’, the drag-free control technology has been tested and demonstrated using the TianQin-1 satellite. In step ‘2’, the inter-satellite laser interferometry technology will be tested using the pair of TianQin-2 satellites. The TianQin-2 mission has been officially approved and the satellites will be launched around 2026. In step ‘3’, i.e. the TianQin-3 mission, three identical satellites will be launched around 2035 to form the space-based GW detector, TianQin, and to start GW detection in space.
19 May 2020 in International Journal of Extreme Manufacturing
25 May 2022 in Classical and Quantum Gravity
The TianQin Project is aiming at gravitational wave (GW) detection in space. TianQin GW observatory comprises three satellites orbiting on 1 × 105 km Earth orbits to form an equilateral-triangle constellation. In order to minimize the variations in arm lengths and breathing angles, the satellites must be launched and adjusted precisely into an optimized orbit. Therefore, satellite laser ranging must be used to enhance the precision of satellite orbit determination. To develop the capability of satellite laser ranging for TianQin’s orbit, the TianQin Laser Ranging Station has been designed and constructed to perform high-precision laser ranging for TianQin satellites and lunar laser ranging as well. Applying a 1064 nm Nd: YAG laser with 100 Hz repetition frequency, 80 pico-second pulse duration, and 2 × 2 array of superconducting nanowire single-photon detectors, we have obtained the laser echo signals from the five lunar retro-reflector arrays, and the measurement data have been packaged into 234 normal points (NPs), including a few data measured during the full-moon lunar phase. Each NP is calculated from continuous measurement for about ten minutes and the statistical error of the NPs is about 7 mm (1σ).
1 June 2018 in Review of Scientific Instruments
Laser link acquisition is a key technology for inter-satellite laser ranging and laser communication. In this paper, we present an acquisition scheme based on the differential power sensing method with dual-way scanning, which will be used in the next-generation gravity measurement mission proposed in China, called Space Advanced Gravity Measurements (SAGM). In this scheme, the laser beams emitted from two satellites are power-modulated at different frequencies to enable the signals of the two beams to be measured distinguishably, and their corresponding pointing angles are determined by using the differential power sensing method. As the master laser beam and the slave laser beam are decoupled, the dual-way scanning method, in which the laser beams of both the master and the slave satellites scan uncertainty cones simultaneously and independently, can be used, instead of the commonly used single-way scanning method, in which the laser beam of one satellite scans and that of the other one stares. Therefore, the acquisition time is reduced significantly. Numerical simulation and experiments of the acquisition process are performed using the design parameters of the SAGM mission. The results show that the average acquisition time is less than 10 s for a scanning range of 1-mrad radius with a success rate of more than 99%.