Liwen Ji

Liwen Ji

Auto-generated profile, based on publicly available information

Liwen Ji

Faculty of Electrical and Control Engineering

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 August 2024 in IEEE Access
Verified
Journal Article
Open access
LJLiwen Ji
Liwen Ji
XLXin Li
Xin Li
LHLei Han
Lei Han
ZYZhen Yang
Zhen Yang
CZCaochao Zhang
Caochao Zhang
YLYan Li
Yan Li
Aiming at the problems of excessive fluctuation and long adjustment time when LLC resonant converter encounters load mutation in traditional control strategy, which seriously affects the normal use, an improved self-disturbance control strategy based on sliding mode control is proposed. The mathematical modeling of LLC resonant converter is carried out by using the method of extended description function to obtain the transfer function of LLC resonant converter. On the basis of linear self-disturbance control, sliding mode control is introduced as the control rate. Through simulation, the steady-state characteristics and dynamic characteristics of LLC resonant converter under three different control strategies of PI (proportional integral controller), LADRC (linear active disturbance rejection control), and SM_ADRC (sliding mode active disturbance rejection control) are compared and analyzed. The simulation results show that the sliding mode active disturbance rejection control is superior to the other two control strategies in improving the response speed and anti-interference ability of LLC resonant converter, with a response time of only 2ms and a ripple of only 0.04V. A small power experimental platform with an output power of 192W is built. The experimental results show that LLC resonant converter can be restored to steady state in a short time by using sliding mode active disturbance rejection control, which effectively improves the dynamic characteristics of the system.

17 March 2025 in ACS Omega
Verified
Journal Article
Open access
ZYZhen Yang
Zhen Yang
LJLiwen Ji
Liwen Ji
XLXin Li
Xin Li
HLHao Li
Hao Li
ZLZhiyong Liu
Zhiyong Liu
HLHaoyuan Liu
Haoyuan Liu
To reveal the coupling relationship between stress, microseismic, and temperature during the deformation and fracture of composite coal and to further study the generation mechanism of deformation and fracture microseismic of composite coal-rock, the SMT (stress-microseismic-thermal) coupled model was derived based on the previously established SCT (stress-charge-thermal) coupled model. The top rock, coal, and bottom rock were extracted to prepare composite coal-rock specimens in the ratios of 1:1:1, 1:2:1, and 1:4:1 and pure coal. The uniaxial loading fracture experiments were carried out on the coal-rock specimens at four different loading rates of 0.1, 0.3, 0.4, and 0.5 mm/min. The variation laws of electromagnetic radiation, microseismic voltage, and temperature signals during the uniaxial loading deformation and fracture process of the composite coal-rock specimens were investigated. The experimental results show that the microseismic voltage and electromagnetic radiation signals are weak at the initial loading stage. The maximum values of the two signals appear when the stress achieves the peak point and the temperature drops on a slight slope. With the increase in the loading rate, the maximum peaks of the two signals decrease, where the change in microseismic voltage is more prominent. In the experiment of different coal-to-rock ratios at 0.5 mm/min, the electromagnetic radiation does not change much, and the peak value of the microseismic voltage signal is the largest in the sample with the coal-to-rock ratio of 1:2:1, followed by that of the pure coal sample. With the thickening of the coal seam, the top rock temperature drops more, indicating that the three signals have a strong consistency and precursor warning function. According to the experimental data, the relationship between the microseismic voltage energy and stress is fitted, and the results show that the two signals are in an excellent exponential relationship and that the fitting coefficient is above 0.9. Combined with the SCT coupling model, the relationship between electromagnetic radiation stress and microseismic voltage energy stress is substituted into the SCT model; then, the induced charge variable is eliminated. The stress-microseismic-temperature (SMT) coupling model is derived. The SMT model is used to fit samples f1-f12, and the coefficients m 2 and z 2 are equipped to verify the fitting. The coefficient of multiple determination R 2 is generally above 0.9, indicating a higher accuracy compared with the SCT model. This suggests that the model has a strong fitting precision and provides a new approach for the prediction and forecasting methods of coal and rock dynamic disasters.