1 July 2025 in Communications - Scientific letters of the University of Zilina
The article is devoted to the study of dynamic interaction of rail track and freight wagons under increased axial load. In conditions of increasing the freight traffic volumes and axial loads, the importance of accurate understanding of the mechanisms affecting the wear of rail track elements becomes especially important. In this paper the authors have carried out experimental research and comparative analysis of freight wagon trolleys of different models. As a result of dynamic tests of the freight wagon trolleys, the necessary parameters of dynamic qualities of different models of wagons and their optimal values of axial loads of freight wagons are obtained. The necessity of improving the current design of wagon trolleys and reinforcing the design of railway track with the use of R65 type rails and reinforced concrete sleepers is substantiated. According to the data of trolley design comparison of different models, the bending moment and maximum load indices are established.
27 June 2025 in Eastern-European Journal of Enterprise Technologies
This paper presents the results of the study of stress-strain state of reinforced concrete spans of two overpasses. With increasing volumes of cargo transportation by rail, the axle load increases up to 25 tons. Bridges and overpasses built about 100 years ago have acquired hidden defects during the years of operation. The safe operation of artificial structures requires additional research using the TENZO software and hardware complex, which processes digital records from primary transducers based on strain gauges. In 2018 and 2023, deflections, strains and stresses were obtained for typical beam spans of 11.5 m and 16.5 m of two reinforced concrete overpasses, from static and dynamic loads. For example, in 2018, the “spread” of stresses from the test load (TEM18) for the right-hand blocks of the 11.5 m spans ranged from 3.7 MPa to 3.71 MPa at different loading stages, and for the left-hand blocks of the 11.5 m spans ranged from 3.46 MPa to 3.9 MPa at different loading stages. In 2023, the stress range was from 2.58 MPa to 4.65 MPa for the right span blocks of 11.5 m span and from 2.67 MPa to 4.7 MPa for the left span blocks at different stages of loading. The 2018 data show uneven loading of the span blocks, indicating that the track axis is offset from the axis of the transportation structure. In 2023, the span structure blocks worked uniformly, which indicates that the track axis and the axis of the transportation structure are aligned (coincide). The obtained dependences “deformations and stresses” for typical beam spans of 11.5 m show the technical condition of the structures of the investigated objects, confirming the possibility of increasing the passage through them of a larger tonnage of transported cargo (increase in axial load up to 25 tons per axle). The spans have demonstrated reliable behavior under dynamic loads, with no signs of significant degradation in the period from 2018 to 2023. The use of data from scientific monitoring methods with the use of digital hardware and software systems will significantly reduce the cost of maintaining artificial structures on railroads and improve the safety of transportation infrastructure
16 March 2025 in International Journal of Innovative Research and Scientific Studies
The article discusses the forces that arise when a TE-33A diesel locomotive moves through a switch. The analysis of dynamic loads acting on rail threads, crosspieces, and other switch elements is carried out. The purpose of this article is to determine the efforts of the TE-33A diesel locomotive acting on the main elements of the railway track switch. The measurements were carried out in accordance with the requirements using a strain gauge measuring and computing complex consisting of certified and verified measuring instruments from the world's leading manufacturers. As a result of theoretical analysis and experimental studies, the lateral and vertical forces transmitted by the wheels to the inner and outer rails of the transfer curve were determined when the TE-33A locomotive was moving along the R65 mark 1/11 switch. Possible causes of increased wear of the switch elements under the influence of the TE-33A diesel locomotive have been identified. Recommendations are proposed to reduce the negative impact on the switches, including optimizing driving modes. Based on the results obtained, diagrams of vertical and transverse forces were constructed, and indicators of the stress rate at maximum speed along the arrow of the locomotive in question were established.
26 August 2025 in International Journal of Innovative Research and Scientific Studies
The results of a theoretical study of the vertical impact of multiaxial locomotives on the track based on the wave theory of elastic deformation propagation are presented. Theoretical and practical problems of dynamic characteristics research at the design stage of modernization of new and existing rail vehicles. Consideration of the impact of compliance with standards on the impact on railway tracks. These issues in the context of crews can be successfully solved using modern methods of analysis and synthesis of dynamic systems. Calculations and practical experiments using modern computer and recording equipment are widely used for dynamic systems. Keywords. Carriage-path, vertical impact of multi-axle locomotives on the track, speed increase, models for analyzing indicators of dynamic qualities of locomotives during vertical fluctuations.
28 March 2025 in Science and Technology of Kazakhstan
В статье рассматривается применение аддитивных технологий в производстве оснастки из полимеркомпозитных материалов, приведены особенности технологического процесса Fused Granular Fabrication (FGF). Представлен процесс создания матрицы для гибки V-образным паза под углом 90° из композитного материала, на основе полимерной матрицы с добавлением стекловолокна для повышения износостойкости. В процессе технологического процесса с использованием композитной матрицы были выявлен тот факт, что пружинение заготовок приктически минимально. В статье приведены результаты сравненения параметров обработки материала на стальной и композиционной полимерной матрицах. По результатам экспериментов очевидно, что для обработки материала с относительно большим внутренним радиусом предпочтительнее использовать полимерную матрицу, поскольку это позволяет снизить усилие давления на 10–20 % при получении одинакового качества продукции Экспериментальные результаты показывают, что использование композиционных полимерных матриц для гибки в мелкосерийном производстве позволяет уменьшить усилие давления, а также снизить стоимость производства по сравнению с традиционными металлическими инструментами. В заключении выделяются преимущества и ограничения применения таких матриц, а также рекомендации для оптимизации процесса гибки и дальнейшего использования в промышленности. Ключевые слова: аддитивные технологии, технология FGF, полимерные материалы, композитные материалы, гибка, V-образный паз, матрица.