Christian Kalscheuer

Christian Kalscheuer

Auto-generated profile, based on publicly available information

Christian Kalscheuer

Surface Engineering Institute RWTH Aachen University Kackertstr. 15 52072 Aachen Germany

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 November 2023 in Surface and Coatings Technology
Verified
Journal Article
Closed access
KBK. Bobzin
K. Bobzin
CKC. Kalscheuer
C. Kalscheuer
MMM.P. Möbius
M.P. Möbius

24 May 2023 in Thin Solid Films
Verified
Journal Article
Closed access
KBK. Bobzin
K. Bobzin
CKC. Kalscheuer
C. Kalscheuer
MCM. Carlet
M. Carlet
JJJ. Janowitz
J. Janowitz

2 November 2023 in Tribology Transactions
Verified
Journal Article
Open access
MRMartin Rank
Martin Rank
MOManuel Oehler
Manuel Oehler
Oliver KochOliver Koch
Oliver Koch
KBKirsten Bobzin
Kirsten Bobzin
CKChristian Kalscheuer
Christian Kalscheuer
MMMax P. Möbius
Max P. Möbius

22 December 2023 in Journal of Vacuum Science & Technology A
Verified
Journal Article
Closed access
PDF file
KBK. Bobzin
K. Bobzin
CKC. Kalscheuer
C. Kalscheuer
MMM. P. Möbius
M. P. Möbius
CSC. Schulze
C. Schulze
MMM. Miranda Marti
M. Miranda Marti
Gears are used in a variety of applications, for example, in automotive and aerospace industries. In these applications, gears are exposed to harsh conditions such as high Hertzian pressures. In many cases, lubricants are used to achieve a reduction in the coefficient of friction and, thus, in the wear of the components. Nevertheless, in some applications, the use of a lubricant is difficult, for example, in vacuum environments. One promising approach is the application of solid lubricants by using triboactive elements. The present study shows the potential of a process combining high power pulsed magnetron sputtering (HPPMS) and direct current magnetron sputtering (dcMS) for the deposition of CrAlN + MoWS coatings. In HPPMS/dcMS processes, especially, the share of HPPMS leads to higher ionization of the coating plasma and, therefore, to higher coating thicknesses on the teeth of gears. One major challenge in coating processes is the adjustment of the deposition temperature, since steels used for gear applications are temperature sensitive. Therefore, starting from an established coating process with a high coating temperature, the coating process was adjusted by reducing the number of used cathodes. By reducing the count of used dcMS cathodes, the share of HPPMS cathodes within the coating process was increased. Furthermore, segments of gears were coated in order to determine the coating thickness at different distances from the head of the gear tooth. A sufficient coating thickness distribution on the flank of the gear tooth is crucial for friction reduction and wear protection when used in gearboxes. The reduction of used cathodes led to a decrease in the coating temperature from a maximum coating temperature of Tmax = 281 °C to Tmax = 214 and 197 °C. It was shown by nanoindentation measurements that the effect of soft annealing was eliminated by reducing the coating temperature. At the same time, coatings deposited with increased HPPMS fraction led to a reduced coefficient of friction as well as lower wear volumes for pin-on-disk measurements in a dry tribological contact with an uncoated 100Cr6 counterpart. Moreover, these processes exhibited a good coatability of the gear tooth with a relatively high coating thickness even near the gear tooth root. The present study shows the potential of increasing the share of HPPMS during the deposition of coatings for dry-running applications. By increasing the HPPMS content, the tribological behavior as well as the coating thickness distribution on gears can be significantly improved.

14 April 2023 in Journal of Vacuum Science & Technology A
Verified
Journal Article
Closed access
PDF file
KBK. Bobzin
K. Bobzin
CKC. Kalscheuer
C. Kalscheuer
MCM. Carlet
M. Carlet
CSC. Schulze
C. Schulze
Physical vapor deposition (PVD) coatings are utilized for wear protection of gears. The use of PVD coatings in unlubricated contacts is also the subject of several research efforts. A promising approach to reduce wear in dry tribological contacts is the combination of MoS2 and WS2 embedded in CrAlN. One possible way to deposit these coatings is the application of High Power Pulse Magnetron Sputtering (HPPMS) process combined with direct current Magnetron Sputtering (dcMS). A challenge by depositing these coatings with an HPPMS/dcMS process is a sufficient adhesion between the coating and the substrate. The present study focuses on the influence of the etching process on the performance of CrAlN + Mo:W:Sg coatings in dry tribological contacts. Before coating deposition, the substrates were pretreated inside the vacuum chamber by different etching processes. During booster etching, which increases the Ar ionization, the substrate bias UB was varied between UB = −150 and UB = −250 V with steps of ΔUB = −50 V. Furthermore, an HPPMS metal ion etching process was used after booster etching at UB = −150 V for these processes. For HPPMS metal ion etching, the number of HPPMS cathodes was varied between one and two. With respect to the etching process, the morphology, surface roughness, compound adhesion by means of the scratch test as well as the coefficient of friction, and the wear volume of the subsequently deposited coatings were investigated. When increasing the substrate bias UB during booster etching, a reduced compound adhesion was found. Moreover, an increased wear volume was observed after pin-on-disk (PoD) tests. For metal ion etching with one activated HPPMS cathode, the wear volume after the PoD test was decreased compared to the pure booster etching processes. When increasing the number of HPPMS cathodes during metal ion etching, the compound adhesion decreased slightly. The wear volume after PoD tests, in contrast, increased. When only using one HPPMS cathode, the lowest wear volume of all investigated coatings was achieved. The present investigations show the potential of tailoring the etching process in order to increase the performance of PVD coatings. A customized HPPMS metal ion etching process can be used to improve the properties of well-established hard PVD coatings.

1 December 2021 in SSRN Electronic Journal
Verified
Preprint
Open access
PDF file
KBKirsten Bobzin
Kirsten Bobzin
CKChristian Kalscheuer
Christian Kalscheuer
MCMarco Carlet
Marco Carlet
NSNina Stachowski
Nina Stachowski
WHWolfgang Hintze
Wolfgang Hintze
PPPetter Ploog
Petter Ploog
Interactions between cutting tool and workpiece material are crucial to tool wear at the cutting edge. In particular difficult to machine materials like the titanium alloy Ti6Al4V require tailored solutions to avoid extensive tool wear. Temperature-active, self-lubricating chromium-aluminium-vanadium-nitride (CrAlVN) coatings deposited by physical vapor deposition (PVD) have shown the potential to reduce tool wear during Ti6Al4V turning. These coatings form lubricating oxide phases at temperatures between 700 °C ≤ ϑ ≤ 800 °C which might be suitable to reduce thermal and mechanical loads during cutting. However, the initial wear development as well as the formation of lubricating oxide phases during Ti6Al4V turning while using cooling lubricant have not been adequately investigated. Consequentially, it is unclear whether the lubricating oxide phases form during the turning operation with flood cooling. Nevertheless, this is of interest, because the use of cooling lubricant is state of the art in turning of Ti6Al4V in order to reach an increased tool life. That is why, the initial tool wear within the first two minutes of turning with flood cooling was investigated in this study. For this purpose, two different CrAlVN coatings with varying V/Al ratios were deposited on cemented carbide inserts by a hybrid direct current magnetron sputtering (dcMS) / high power pulsed magnetron sputtering (HPPMS) process using an industrial coating unit. Subsequently, cutting tests with a depth of cut ap = 1.2 mm, feed rate f = 0.12 mm, setting angle κr = 95° and cutting velocity vc = 80 m/min were conducted at defined cutting intervals of tc = 5 s, 10 s, 20 s, 40 s, 80 s and 120 s using a computer numerical controlled (CNC) lathe machine. The initial tool wear development, prevailing wear mechanisms as well as the formed oxide phases during the intervals were analyzed. Uncoated cemented carbide inserts were used as a reference. The results highlight that the formation of lubricating vanadium oxides is possible in turning process with cooling lubricant. Furthermore, it seems that adhesion processes are the main causes of tool failure. The results offer the possibility to adapt the CrAlVN coatings for Ti6Al4V turning.