João Batista Ferreira Neto

João Batista Ferreira Neto

Auto-generated profile, based on publicly available information

João Batista Ferreira Neto

Laboratory of Metallurgical Processes, Institute for Technological Research (IPT), São Paulo, Brazil

Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 October 2015 in Journal of Sustainable Metallurgy
Verified
Journal Article
Open access
PDF file
JNJoão B. Ferreira Neto
João B. Ferreira Neto
JFJoão O. G. Faria
João O. G. Faria
CFCatia Fredericci
Catia Fredericci
FCFabiano F. Chotoli
Fabiano F. Chotoli
Andre Luiz Nunis da SilvaAndre Luiz Nunis da Silva
Andre Luiz Nunis da Silva
ALAndre A. Lotto
Andre A. Lotto
The use of metallurgical slags in cement production depends on the phases present in such slags, which are affected by changes in slag composition as well as the cooling rates adopted during solidification. In this work, slags with distinct chemical compositions were melted and subjected to different cooling conditions. Slag samples were characterized by X-ray diffraction to identify and quantify mineralogical phases and by X-ray fluorescence to determine chemical composition. The microstructure of the samples was characterized by scanning electron microscopy coupled to energy dispersive spectroscopy for phase identification. The solidification of the slags was simulated using FactSage™ for solidification path evaluation, enabling a comparison of the phases determined by thermodynamic equilibrium with those analysed in slag samples. Slags with low basicity (CaO/SiO2 <1.25) and Al2O3 content of 11 wt% exhibited a high glassy phase content depending on the cooling conditions. The phases formed in slags with higher basicity (1.4 and 3.8) were less affected by cooling rate and were different silicates, such as larnite, merwinite, monticellite, akermanite, gehlenite and melilite, whereas slags with basicity ≥1.37 exhibited RO phase (solid solution of FeO, MgO, CaO and MnO).

19 June 2017 in Journal of Sustainable Metallurgy
Verified
Journal Article
Closed access
PDF file
FNFerreira Neto
Ferreira Neto
JBJoão B.
João B.
CFCatia Fredericci
Catia Fredericci
JFJoão O. G. Faria
João O. G. Faria
FCFabiano F. Chotoli
Fabiano F. Chotoli
ALAndre A. Lotto
Andre A. Lotto

10 November 2008 in Anais Congresso Brasileiro de Energia Solar - CBENS
Verified
Conference Paper
Open access
PDF file
JNJoão Batista Ferreira Neto
João Batista Ferreira Neto
TOTheogenes Silva de Oliveira
Theogenes Silva de Oliveira
MMMarcelo de Aquino Martorano
Marcelo de Aquino Martorano
The demand for solar grade silicon (SiGS) in the photovoltaic industry has grown 35% per year and a constant growth rate is predicted for the next decade. The availability of f eedstock to produce SiGS, however, has not grown at the same rate, resulting in increasing SiGS cost. Consequently, the development of less expensive alternative processing routes is of paramount importance to the photovoltaic industry in general, and particularly to Brazil, which is the 3rd largest producer of metallurgical grade silicon. The objective of the present work is to study the directional solidification of silicon, which is a step adopted in virtually all alternative processing rout es under development to refine silicon. The directional solidification of silicon was ca rried out in a vertical Bridgman furnace, where liquid silicon was poured into a quartz mold, which was extracted at constant velocity from the hot region of the furnace, resulting in ascending directional solidification. Two types of feedstock silicon were used, namely, a metallurgical grade silicon that was refined by leaching prior to directional solidification and metallurgical grade silicon as-received from the manufacturer. The quartz molds with liquid silicon were extracted at four different velocities in the range from 5 to 110 μm/s. In the solidified silicon ingots, the macrosegregation of elements were measured using accurate analytical techniques, whereas the metallurgical structures were observed in macro and micrographs. The ingots solidified at lower extraction velocities, at which evidences of a planar solid-liquid interface were observed, showed greater refining effect than those solidified at larger velocities, which showed evidences of a cellular or dendritic solid-liquid interface. A demanda do silício de grau solar (SiGS), utilizado na indústria de células solares fotovoltaicas, cresce atualmente em uma média de 35% ao ano e a projeção para a próxima década é de constante crescimento. Entretanto, a disponibilidade desta matéria-prima não tem crescido na mesma taxa, resultando em uma elevação de seu custo. Tendo como objetivo a purificação do silício, o presente trabalho de pesquisa apresenta um estudo detalhado da solidificação direcional do silício. Este estudo foi realizado em um forno do tipo Bridgman vertical, onde o silício líquido contido em um molde foi extraído da região quente do forno, resultando em uma solidificação direcional controlada e ascendente. Dois tipos de silício foram escolhidos como material de entrada para o processo de refino: o silício de grau metalúrgico e o silício de grau metalúrgico pré-refinado por lixiviação. Quatro velocidades de extração do molde entre 5 a 110 μm/s foram empregadas nos ensaios. A macrossegregação de impurezas nos lingotes obtidos foi medida através de análises químicas e a estrutura metalúrgica observada através de macro e micrografias. Os lingotes solidificados com menor velocidade de extração, onde se observa evidências de uma interface sólido-líquido plana, apresentam um grau de refino superior aos de maior velocidade.