Protests during the 2021 Climate Conference in Glasgow exemplified our dilemma. The establishment perpetuates old thinking, while young people demand a new approach to mitigate the impact of climate change. The authors agree with the young people, and as a solution we propose to replace the current fragmentary approach with a new holistic one. The passive house approach that was conceptualized by the University of Illinois and built in Canada in 1977 showed us that energy consumption can be reduced about half of that used in the traditional design. Seventeen years later, a European passive house was built in Darmstadt. In 2008, a demonstration house in Syracuse, NY, showed that integrated passive measures produced energy use by about half of the NY state code for 2004. At the same time, some advanced houses in the USA showed total energy use of about 70 kWh/(m2∙y). In 2008, at the first Building Enclosure Science and Technology Conference, two equally important objectives for 2030 were proposed by the Lawrence Berkeley National Laboratory: (1) a 90% reduction of energy use in new buildings and (2) 50% for the retrofitting of existing buildings, i.e., to the level achieved in the 1980s. The first objective has recently been achieved in small buildings while the large residential buildings remain on the level obtained in the 2000s. Yet, the retrofitting of existing buildings (the second objective) has been a dismal failure. This paper acknowledges progress in hydronic heating and cooling involving electric heat pumps and hybrid solar panels, building automatics used for operation of HVAC, and modification of air distribution systems that comes from experience with the SARS-CoV-2 pandemic. Furthermore, it highlights that to accelerate energy efficiency and carbon emission reductions, there must be broad public-private educational programs with demonstrations of a new generation of retrofitting. Economically and ecologically retrofitted buildings will create a new approach to real estate investment.
A solution to the inordinate amount of energy used for climate control in buildings is of paramount importance if we are to significantly reduce our dependence on fossil fuels in a relatively short time. A large quantity of low-grade energy is available in the earth surrounding a typical residential structure. This energy is often tapped for use in heating and cooling in conjunction with a ground source heat pump. Efficient use of this energy source can be realized without the expense of a heat pump by designing a green system directly integrating the ground source with a dynamic building envelope. This paper explains the concept of the ground-coupled dynamic (GCD) wall, which can be easily retrofitted in some form to most existing structures to capture and use this low-grade energy. It makes use of clean renewable resources without excessive amounts of expensive or high-tech equipment. The paper demonstrates that in conjunction with an exergy management system, the application of this concept could significantly lower residential fossil fuel consumption.
Commonly used terms such as form, function, and behavior often take on varying definitions in the literature related to product design and development. This is especially true as the point of reference moves through various stages of development from conceptual design, through product disposal. This can become problematic from the standpoint of interpretation and implementation when an information model is being created that is intended to be useful to a product throughout its entire lifecycle. A product changes throughout its useful life, so a lifecycle model of a product must also be dynamic and able to grow and age with it. If this is to be the case, descriptive terms and definitions should be specific and retain their definition throughout the life of the model. In this paper, we attempt to select a set of terminology that can be uniquely descriptive of the classes needed to define a product lifecycle model. Terms such as form, function, affordance and behavior are defined within a hierarchy of a product’s lifecycle development. Terminology as presented in this context becomes less ambiguous. An example of a home-shop built pendulum clock serves to illustrate the utility of this new design lexicon. The terminology outlined here may not be optimal and significant additions and alterations may be justifiably suggested; but it is hoped that this paper will begin a dialogue eventually resulting in the elimination of much ambiguity in product modeling terminology.
A decade ago, Geo-solar Exergy Storage Technology (GEST) was introduced as a means of utilizing natural, diurnal and seasonal transfers of exergy between a building and its surroundings to significantly decrease heating and cooling requirements. This is accomplished by retrofitting the structure with a dynamic skin to the existing building enclosure that is provided with internal conduits to carry air and fluids, for coupling geothermal storage surrounding the building with the exterior environment. This system was developed by engineers as an affordable, low-tech solution for providing seasonal heat storage in cold climate regions. Meanwhile another holistic but high-tech means to the same goal was initiated by an international group of building scientists by defining concepts for environmental quality management (EQM). Using heat pumps, ‘smart controls’, and newly developed wall coating materials, a fully integrated HVAC (plus moisture control and indoor air quality (IAQ)) system was proposed. The experience gained with GEST methods is now combined with the leading edge of Building Science to permit our international team to re-evaluate the concept of Geo-solar Exergy Storage and Dynamic Building Enclosure incorporated in a system with a heat pump as a new basis for retrofitting buildings in any climate.