13 March 2020 in IEEE Antennas and Wireless Propagation Letters
A compact single-layer filtering microstrip antenna with diverse characteristics of low-profile, high-gain, wideband and high-selectivity is proposed in this paper. Simple structure as it is, the presented antenna mainly consists of a rectangle driven patch, four parasitic strips, a pair of symbiotic strips and a set of shorting pins. By attaching four parasitic strips to the original rectangular patch antenna, an additional resonance can be excited while the high-band edge selectivity is greatly improved due to the formation of a radiation null outside. Then, two symbiotic strips are embedded on both sides of the driven patch, which in turn creates an extra resonance mode and a lower-band radiation null. The set of shorting pins are applied to further improve operating and filtering response. Finally, the use of two parasitic patches can effectively improve the level of impedance bandwidth (IBW) and upper-band suppression. To verify this design, the corresponding antenna is fabricated and tested. The measured and simulated results are highly consistent, which reveals that it owns a wide IBW of 20.1% (2.19-2.68GHz) with three resonance points, a higher average gain large than 9.5dBi and a flat radiation efficiency above 88% in-band. The suppression level of the out-of-band gain on both sides can reach 14.5dB.
1 June 2020 in IEEE Antennas and Wireless Propagation Letters
A compact dual-polarized filtering base-station antenna is presented in this paper. The antenna with stacked structure is mainly consisted of main radiators, coupled and filtering structure, dual-polarized dipoles, feeding networks, metal wall and reflector. Four vertical slots etched on each branch of the coupled cross is for improving the high frequency suppression of the antenna. The C slots on the ground reduce the cross-polarization ratio of the antenna at the axial direction. The entire size (include the ground plane) of the element is only 0.53λ×0.72λ×0.14λ (λ is the wavelength of the central frequency) and the antenna shows a wide working band of 25% and a low cross polarization ratio about 22dB. In order to validate the design, a 1x3 linear array is fabricated and tested. The antenna array works at 3.3-4.0 GHz which meets the demand of 5G applications. Within the operation band, the average gain of the array is about 11dBi. Besides, the antenna array remains a good out of band rejection more than -20dB up to 9GHz which exhibits a good harmonic suppression performance over a wideband.
28 March 2022 in IEEE Transactions on Antennas and Propagation
In this article, a compact differentially fed ±45° dual-polarized filtering magneto-electric (ME) dipole antenna with improved harmonic suppression is proposed and analyzed. First, the fusion of loop-slot dipole and half-wave vibrator is calculated and mentioned to furnish theoretical guidance. Then, by reasonably placing two pairs of second-order step impedance feedlines and a loop-slot patch, a corresponding two-mode loop-vibrator combination filtering antenna with an upper radiation null is naturally constructed. Moreover, simply by loading four open-circuit stubs at the center of octagonal slot patch edge, another extra resonance mode and radiation null in the upper band can be simultaneously obtained. Later, through hiring the reconstructed third-order stub-loaded-resonator (SLR) feedlines, wideband harmonic suppression along with a third radiation null is unaffectedly achieved. Finally, the optimized antenna is fabricated and tested. The measured results reveal it realizes a wideband impedance bandwidth of 42.0% (2.78–4.26 GHz) and a high port isolation of 35 dB. Also, the length of its harmonic suppression is measured from 4.56 to 7 GHz, while the depth reaches more than 20 dB. In addition, the measured gain and radiation efficiency curves in the operating band are relatively stable and both are at a high average value (8.2 dBi, 85%).
30 May 2022 in IEEE Transactions on Antennas and Propagation
In this communication, two compact co-polarized decoupled microstrip patch array antennas based on TM02/TM03 modes cancellation are proposed. It is only necessary to introduce shorting pins and etch slots on the patch antenna to precisely adjust the frequency and impedance of TM02 and TM03 modes to make them consistent, which can significantly reduce the strong coupling between the tightly spaced patch antennas. In addition, the L-shaped open-stub coupling feeding is used to eliminate the parasitic inductance caused by the shorting pins to achieve better impedance matching. Finally, the proposed two/eight-port microstrip patch array antennas are fabricated and measured. The simulation and measurement results show that the coupling of adjacent ports is decreased lower than -30 dB within the impedance matching bandwidth (3.42 - 3.58 GHz), while the edge-to-edge spacing is only 0.023 λ0 between the antenna elements. With the advantages of simple design, significant decoupling effect, and good radiation performance, the proposed decoupling scheme has broad application prospects in 5G array antennas.
5 October 2022 in IEEE Antennas and Wireless Propagation Letters
A hybrid frequency selective rasorber is presented in this paper based on hybrid lossy layers. The hybrid lossy layers is composed of an Absorption-Transmission(A-T) layer and a Transmission-Absorption(T-A) layer, which are responsible for the absorption performance in the low and high frequency respectively. The A-T layer is composed of a lumped-resistors loaded cross-frame structure(CFS), which connects four parallel inductor and capacitor resonators. The T-A layer is constructed by a parallel plate capacitor loaded square loop resonator connecting four lumped-resistor loaded T-shaped metal branches. The FSS layer is composed of metal square slot. The hybrid FSR provides a transmission window around 10GHz and two-sided absorption bands in 3.19GHz-9GHz and 11.85GHz-21.18GHz, meanwhile the wideband reflection suppression(S 11 <-10dB) is achieved from 3.2 to 21.18GHz (147%). An assembled prototype is measured to verify the simulated results.
28 April 2023 in IEEE Antennas and Wireless Propagation Letters
In this paper, a dual-band frequency selective rasorber(FSR) is proposed based on a composite absorption structure. The FSR is a three-tier structure composed of lossy layer I, lossy layer II and a dual-band frequency selective surface (FSS). The lossy layer I is composed of a lossy cross-shaped structure in which, dual-passband resonators are added and constructed by parallel interdigital capacitors and meandering strip inductors(PLC). The lossy layer II is composed of a hybrid circular strip resonator loaded with lossy elements. FSS is implemented in two Jerusalem slots. By combining the lossy layers I and II as a composite lossy structure, the absorption bands of lossy layers I and II are successfully connected in the frequency response, and the bandwidth of S 11 under -10dB is extended from 3.1 to 20.6GHz. The proposed FSR integrate dual-band, dual-polarized, and broadband absorption performance simultaneously. Finally, a prototype of the composite FSR is fabricated to validate the simulated results.