1 February 2019 in APL Photonics
We present a low-loss integrated photonics platform in the visible and near ultraviolet (UV) regime. Fully etched waveguides based on atomic layer deposition (ALD) of aluminum oxide operate in a single transverse mode with <3 dB/cm propagation loss at a wavelength of 371 nm. Ring resonators with intrinsic quality factors exceeding 470 000 are demonstrated at 405 nm, and the thermo-optic coefficient of ALD aluminum oxide is estimated to be 2.75 × 10−5 (RIU/°C). Absorption loss is sufficiently low to allow on-resonance operation with intra-cavity powers up to at least 12.5 mW, limited by available laser power. Experimental and simulated data indicate that the propagation loss is dominated by sidewall roughness, suggesting that lower loss in the blue and UV is achievable.
22 August 2019 in Optics Letters
Precise knowledge of a laser’s wavelength is crucial for applications from spectroscopy to telecommunications. Here, we present a wavemeter that operates on the Talbot effect. Tone parameter extraction algorithms are used to retrieve the frequency of the periodic signal obtained in the sampled Talbot interferogram. Theoretical performance analysis based on the Cramér–Rao lower bound as well as experimental results are presented and discussed. With this scheme, we experimentally demonstrate a compact and high-precision wavemeter with below 10 pm single-shot estimation uncertainty under the criterion around 780 nm.
7 August 2024 in Optics Express
Inverse design of optical components based on adjoint sensitivity analysis has the potential to address the most challenging photonic engineering problems. However, existing inverse design tools based on finite-difference-time-domain (FDTD) models are poorly suited for optimizing waveguide modes for adiabatic transformation or perturbative coupling, which lies at the heart of many important photonic devices. Among these, dispersion engineering of optical waveguides is especially challenging in ultrafast and nonlinear optical applications involving broad optical bandwidths and frequency-dependent anisotropic dielectric material response. In this work, we develop gradient back-propagation through a general-purpose electromagnetic eigenmode solver and use it to demonstrate waveguide dispersion optimization for second harmonic generation with maximized phase-matching bandwidth. This optimization of three design parameters converges in eight steps, reducing the computational cost of optimization by ∼100x compared to exhaustive search and identifying new designs for broadband optical frequency doubling of laser sources in the 1.3–1.4 µm wavelength range. Furthermore, we demonstrate that the computational cost of gradient back-propagation is independent of the number of parameters, as required for optimization of complex geometries. This technique enables practical inverse design for a broad range of previously intractable photonic devices.
23 December 2024 in Applied Physics Letters
Patterning of stable, spatially tailored ferroelectric domains in thin-film lithium niobate enables efficient nonlinear optical interactions through quasi-phase matching. The engineering of domain structure is limited by the uncontrolled distribution of defects, which disrupt domain wall motion. Here, we fabricate quasi-phase matching gratings in thin-film lithium niobate with sub 20 nm of period variation. We demonstrate that annealing processed samples at 350 or 500 °C for 48 h, prior to E-field poling, can dramatically reduce the duty cycle variation. We show that maintaining an elevated temperature of 200 °C during poling enhances defect mobility, which leads to more rectangular inverted domains. Moreover, poling at elevated temperatures also increases inversion depth without sacrificing the periodic domain pattern's accuracy or precision. Elevating the temperature prior to and during poling resulted in near-ideal square wave patterning of ferroelectric domains (50% mean duty cycle, sub 10% domain width variation, and 100% depth inversion). This enables effective quasi-phase matching for second harmonic generation in 5.6 mm-long waveguides fabricated from MgO-doped x-cut thin-film lithium niobate.
7 June 2022 in Optics Express
Photonically integrated resonators are promising as a platform for enabling ultranarrow linewidth lasers in a compact form factor. Owing to their small size, these integrated resonators suffer from thermal noise that limits the frequency stability of the optical mode to ∼100 kHz. Here, we demonstrate an integrated stimulated Brillouin scattering (SBS) laser based on a large mode-volume annulus resonator that realizes an ultranarrow thermal-noise-limited linewidth of 270 Hz. In practice, yet narrower linewidths are required before integrated lasers can be truly useful for applications such as optical atomic clocks, quantum computing, gravitational wave detection, and precision spectroscopy. To this end, we employ a thermorefractive noise suppression technique utilizing an auxiliary laser to reduce our SBS laser linewidth to 70 Hz. This demonstration showcases the possibility of stabilizing the thermal motion of even the narrowest linewidth chip lasers to below 100 Hz, thereby opening the door to making integrated microresonators practical for the most demanding future scientific endeavors.
18 July 2023 in Optics Express
The use of averaging has long been known to reduce noise in statistically independent systems that exhibit similar levels of stochastic fluctuation. This concept of averaging is general and applies to a wide variety of physical and man-made phenomena such as particle motion, shot noise, atomic clock stability, measurement uncertainty reduction, and methods of signal processing. Despite its prevalence in use for reducing statistical uncertainty, such averaging techniques so far remain comparatively undeveloped for application to light. We demonstrate here a method for averaging the frequency uncertainty of identical laser systems as a means to narrow the spectral linewidth of the resulting radiation. We experimentally achieve a reduction of frequency fluctuations from 40 Hz to 28 Hz by averaging two separate laser systems each locked to a fiber resonator. Only a single seed laser is necessary here as acousto-optic modulation is used to enable independent control of the second path. This technique of frequency averaging provides an effective solution to overcome the linewidth constraints of a single laser alone, particularly when limited by fundamental noise sources such as thermal noise, irrespective of the spectral shape of noise.