Amund Ruud

Amund Ruud

Auto-generated profile, based on publicly available information

Amund Ruud

Nordic Institute of Dental Materials, NIOM, Oslo, Norway

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 April 2020 in Crystal Growth & Design
Verified
Journal Article
Open access
OFOystein Slagtern Fjellvag
Oystein Slagtern Fjellvag
ARAmund Ruud
Amund Ruud
HSHenrik Hovde Sonsteby
Henrik Hovde Sonsteby
Ola NilsenOla Nilsen
Ola Nilsen
HFHelmer Fjellvåg
Helmer Fjellvåg
Insight to the crystallization process of functional materials deposited as thin films in an amorphous state is essential when phase pure samples of specific polymorphs are sought for utilization of performance aspects or fundamental studies. In this work, we report on controlled crystallization of α- and β-MoO3 polymorphs from amorphous MoO3 thin films produced by atomic layer deposition (ALD). The MoO3 films are amorphous as deposited. Our experiments show that β-MoO3 starts to crystallize from amorphous MoO3 at a surprisingly low temperature of 185 °C, only 20 °C above the adopted ALD deposition temperature. Thin films of the β-MoO3 polymorph start slowly to convert into α-MoO3 at temperatures above 300 °C; however, long holding times are required to obtain phase pure products. High-quality thin film samples (electrodes) were characterized by electrochemical cycling towards lithium, demonstrating that α- and β-MoO3 transfers into the same chemical state during cycling and that amorphous MoO3 undergoes less change upon cycling.

28 April 2020 in Physical Chemistry Chemical Physics
Verified
Journal Article
Open access
PDF file
Abdel El KharbachiAbdel El Kharbachi
Abdel El Kharbachi
JWJulia Wind
Julia Wind
ARAmund Ruud
Amund Ruud
AHAstrid B. Høgset
Astrid B. Høgset
MNMagnus M. Nygård
Magnus M. Nygård
BHBjørn C. Hauback
Bjørn C. Hauback
LiCl1−x(BH4)x stabilized by P2S5 addition with high Li+ conduction; further operando XRD in transmission mode of a solid-state battery demonstrated.

2 March 2024 in Journal of Dentistry
Verified
Journal Article
Open access
AGAbdulaziz Gul
Abdulaziz Gul
EPEvaggelia Papia
Evaggelia Papia
ANAron Naimi-Akbar
Aron Naimi-Akbar
ARAmund Ruud
Amund Ruud
PSPer Vult von Steyern
Per Vult von Steyern
To evaluate the clinical outcome of different designs of zirconia dental implants. This systematic review adhered to the PRISMA checklist and followed the PICO framework. The protocol is registered in PROSPERO (CRD42022337228). The search was conducted in March 2023 through four databases (PubMed, Web of Science, Cochrane Library, and Google Scholar) along with a search of references in the related reviews. Three authors reviewed on title, and abstract level and analysed the risk of bias, and all authors reviewed on a full-text level. Clinical studies excluding case reports for patients treated with different designs of zirconia dental implants were included. From a total of 2728 titles, 71 full-text studies were screened, and 27 studies were included to assess the risk of bias (ROBINS-I tool) and data extraction. After quality assessment, four studies were included, and the remaining 23 excluded studies were narratively described. The included prospective studies with moderate risk of bias reported success and survival rates of one-piece implants that ranged between 95 and 98.4 % with no difference between different lengths and diameters. The acid-etched roughened surface showed higher clinical outcomes compared to other surface roughness designs. Promising 5-year clinical outcomes were found for one-piece zirconia implants with no difference between different diameters and lengths. Concerning surface roughness, better outcomes were found when using the acid-etched implant surface. However, due to the limited available studies, further high-quality clinical studies comparing zirconia one-piece and two-piece implants with different diameters, lengths, and surface roughness are needed. Based on this systematic review, under suitable clinical situations, the one-piece zirconia implants with diameters of 4.0 mm, 4.5 mm, or 5.5 mm and lengths of 8 mm, 10 mm, 12 mm, or 14 mm have similar promising clinical outcomes. Additionally, the acid-etched roughened implant surface may be preferable.

9 November 2018 in Physical Chemistry Chemical Physics
Verified
Journal Article
Closed access
PDF file
ARAmund Ruud
Amund Ruud
JSJonas Sottmann
Jonas Sottmann
VPVajeeston Ponniah
Vajeeston Ponniah
HFHelmer Fjellvåg
Helmer Fjellvåg
Conversion and alloying reactions in BiVO 4 as an anode material for lithium-ion batteries.

3 July 2019 in Journal of Materials Chemistry A
Verified
Journal Article
Closed access
PDF file
ARAmund Ruud
Amund Ruud
JSJonas Sottmann
Jonas Sottmann
PVPonniah Vajeeston
Ponniah Vajeeston
HFHelmer Fjellvåg
Helmer Fjellvåg
Bi 2 (MoO 4 ) 3 has been evaluated as an interesting anode material for application in lithium-ion batteries (LIBs).

6 August 2020 in Journal of Vacuum Science & Technology A
Verified
Journal Article
Closed access
PDF file
JKJulie N. Kvalvik
Julie N. Kvalvik
KKKristian B. Kvamme
Kristian B. Kvamme
KAKjetil Almaas
Kjetil Almaas
ARAmund Ruud
Amund Ruud
HSHenrik Hovde Sonsteby
Henrik Hovde Sonsteby
Ola NilsenOla Nilsen
Ola Nilsen
Lithium fluoride (LiF) is an integral part of UV optics. Recently, it has also gained attention for its role in the solid-electrolyte interphase on the anode of lithium-ion batteries. Atomic layer deposition (ALD) is the preferred tool for synthesizing conformal and pin-hole free LiF thin films, especially on high aspect ratio structures. Present routes to deposit LiF by ALD are based on HF or HF-pyridine as the fluorine source, requiring strict safety precautions. Other routes involve TiF4 or WF6, resulting in inclusions of Ti or W impurities in the resulting films. Herein, we present a new route to deposit LiF by ALD, using lithium tert-butoxide (LiOtBu) and NH4F as precursors. The process yields uniform films over a broad temperature range (150–300 °C), with a growth per cycle of 50.9 pm/cycle (225 °C). The films are free from any nitrogen contamination from the NH4F precursor. This process provides a facile route for high purity LiF thin films with the use of less harmful precursor chemistry.