3 January 2018 in IEEE Transactions on Components, Packaging and Manufacturing Technology
In this paper, for the first time, we designed and analyzed channels between a graphic processing unit and memory in a silicon interposer for a 3-D stacked high bandwidth memory (HBM). We thoroughly analyzed and verified the electrical characteristics of the silicon interposer considering various design parameters, such as the channel width and space, redistribution layer via, and under bump metallurgy pads. In particular, we also considered the meshed ground planes used for the proposed transmission lines, which are microstrip and strip lines. Signal integrity (SI) of the proposed channels in the silicon interposer was successfully analyzed and verified using a full 3-D electromagnetic solver and circuit simulations. Based on the extracted lumped circuit resistance, inductance, conductance and capacitance parameters, we thoroughly analyzed the channel characteristics and identified the parameters that dominantly affect SI in relation to each frequency range. From the analyzed insertion loss and far end crosstalk, we verified SI of the silicon interposer by eye-diagram simulations in terms of eye-height voltage and timing jitter in the time domain. In the worst case, the eye-height voltage and timing jitter of the proposed microstrip lines are 0.911 V and 36.8 ps, respectively, with 72 mV of signal coupling. The eye-height voltage and timing jitter of the proposed strip line are 0.887 V and 42.1 ps with 34 mV of single couplings. We show that the proposed channels of the silicon interposer can successfully transfer data at a 2-Gb/s data rate. Finally, we propose concepts and solutions for the next-generation HBM interface with higher data rates up to 8 Gb/s.
25 December 2017 in IEEE Transactions on Electromagnetic Compatibility
This letter proposes a fast and precise high-speed channel modeling and optimization technique based on machine learning algorithms. Resistance, inductance, conductance, and capacitance (RLGC) matrices of a high-speed channel are precisely modeled by design-of-experiment method and artificial neural network. In addition, an optimal channel design, which achieves minimum channel loss and crosstalk, is investigated within short time by a genetic algorithm. The performance of the proposed technique is validated by simulations up to 20 GHz.
9 November 2017 in IEEE Transactions on Electromagnetic Compatibility
Precise analytical models of power supply noise induced jitter (PSIJ) at inverter chains are proposed. Based on the piecewise linear approximated I–V curve model, analytical models of local PSIJ transfer functions at local rising and falling edges are derived. The total PSIJ transfer function of an inverter chain output is then estimated by alternately accumulating the local PSIJ transfer function at local rising and falling edges. Based on several assumptions, the full PSIJ transfer function model is significantly simplified, which provides physical insights of PSIJ at inverter chains. Accuracy of the proposed analytical model is successfully validated by SPICE simulations with 130 nm CMOS technology. In addition, properties of the PSIJ transfer function at inverter chains are analyzed based on the proposed model.
1 November 2017 in IEEE Transactions on Electromagnetic Compatibility
This paper, for the first time, proposes a novel stochastic model-based eye-diagram estimation method for 8B/10B and transition-minimized differential signaling (TMDS)-encoded high-speed channels. A stochastic model describes a behavior of an encoder with respect to probability. The previous eye-diagram estimation methods are based on an assumption that each bit has the same probability for 1 s and 0 s. However, the assumption limits to estimate an accurate eye-diagram for encoded high-speed channels. We first propose and apply the stochastic model for two types of 8B/10B encodings: 8B/10B and TMDS. For verification, we design the 8B/10B and TMDS encoder within MATLAB. The transient simulation for the 8B/10B encoded channels requires 9700 and 6600 s, respectively. However, the proposed method only requires 23 s in both cases. Furthermore, in the bit-error rate, the transient simulation provides the bathtub curve up to ${10^{ - 2}}$ due to processing time and computing resources. In contrast, the proposed method with the stochastic model provides the bathtub curve up to ${10^{ - 8}}$. In conclusion, this paper successfully proposes and verifies the stochastic model-based eye-diagram estimation method for 8B/10B-encoded high-speed channels.
11 April 2022 in IEEE Transactions on Microwave Theory and Techniques
In this article, a novel training set optimization method in an artificial neural network (ANN) constructed for high bandwidth interconnects design is proposed based on rigorous probability analysis. In general, the accuracy of an ANN is enhanced by increasing training set size. However, generating large training sets is inevitably time-consuming and resource-demanding, and sometimes even impossible due to limited prototypes or measurement scenarios. Especially, when the number of channels in required design are huge such as graphics double data rate (GDDR) memory and high bandwidth memory (HBM). Therefore, optimizing the training set selection process is crucial to minimizing the training datasets for developing an efficient ANN. According to rigorous mathematical analysis of the uniformity of the training data by probability distribution function, optimization flow of the range selection is proposed to improve accuracy and efficiency. The optimal number of training data samples is further determined by studying the prediction error rates. The performance of the proposed method in terms of accuracy is validated by comparing the scattering parameters of arbitrarily chosen strip and microstrip type GDDR interconnects obtained from EM simulations with those predicted by ANNs using default and the proposed training-set selection methods.