The need for nano-antennas with decreased size and the capacity to operate at mid-infrared frequencies to enable adequate coverage of signal is being investigated. In this paper, we present graphene-based nano-antenna and analysed at the resonating frequency 33 THz using gallium arsenide material as a substrate having dielectric constant 11.35 and a loss tangent of 5.6×10-4 for terahertz (THz) frequency. The height of substrate is optimized to 108 nm and in-plane dimension being 1,700×1,400 nm. Graphene was used as a rectangular patch with dimension 850×450×5 nm and ground having chemical potential=1.4 eV, and relaxation time=1 ps, to achieve high gain and bandwidth. Impact of slot width variation on the antenna parameters have been reported in terms of reflection coefficient (S11), voltage standing wave ratio (VSWR), radiation pattern and gain. Reported beam width being 90.4° for both electric and magnetic planes. Proposed antenna achieved a return loss of -18.38 dB, VSWR less than 2, indicating good match with load, highest gain of 8.8 dBi and bandwidth of 500 GHz at the target resonance frequency making it suitable for 5G/6G mm wave wireless communication.
1 February 2025 in Indonesian Journal of Electrical Engineering and Computer Science
This paper reports design and results of a microstrip patch antenna for broadband application in the millimeter wave communication with multiband features. Electromagnetic solver high-frequency structure simulator (HFSS) is employed to measure the effectiveness of the electromagnetic properties and electrical behaviour of the antenna. The proposed microstrip patch antenna (MPA) can be easily fabricated on a single substrate using standard photolithography process to attach the radiating element and feed lines to the dielectric material. On a 4.93 mm×5.86 mm metallic patch, over FR4 epoxy substrate with dielectric constant 4.4 and loss tangent 0.03, two L-shaped slots are placed along with a few micro slots of varied dimensions, and the antenna is fed with microstrip feedline with resistive load termination of 50 Ω. Pentaband resonant frequencies are realized in the K-band at 13.6 GHz, 23.2 GHz, 29.68 GHz, 32.96 GHz, and 38.56 GHz, with minimum return loss of -23.17 dB, bandwidth 2.32 GHz, omnidirectional radiation pattern, and maximum reported gain of 4.5 dB. The designed antenna achieved good electromagnetic radiation properties and electrical behaviour, and is a good choice for broadcasting over short distances, surveillance and monitoring, wireless sensor backhauls and telecommunication in the K-band networks.
A novel high-entropy perovskite, Ba($ \mathrm{Ti_{0.2}}\mathrm{Zr_{0.2}}\mathrm{Hf_{0.2}}\mathrm{Sn_{0.2}}\mathrm{Ce_{0.2}} $) $ \mathrm{O_3} $, was successfully synthesized through a conventional solid-state reaction route and finally sintered at 1350°C for 12 h. Powder X-ray diffraction and Rietveld refinement confirmed the formation of a single-phase cubic structure with space group Pm$ \overline{{3}}m $. Scanning electron microscopy coupled with EDX mapping revealed an uniform microstructure and homogeneous elemental distribution. The electrical properties were investigated using impedance spectroscopy over a temperature range of 35 to 495°C and a frequency range of 100Hz to 1MHz. The real part of impedance decreased with increasing temperature, indicating negative temperature coefficient of resistance (NTCR) behaviour. The imaginary impedance and electrical modulus spectra exhibited temperature-dependent relaxation with peak shifting toward higher frequencies, confirming thermally activated charge transport. The Nyquist plot analysis revealed separate contributions from grains and grain boundaries, demonstrating mixed bulk and interfacial conduction mechanisms. These results establish Ba($ \mathrm{Ti_{0.2}}\mathrm{Zr_{0.2}}\mathrm{Hf_{0.2}}\mathrm{Sn_{0.2}}\mathrm{Ce_{0.2}} $) $ \mathrm{O_3} $ as a promising candidate for high-temperature electronic and sensing applications.
1 February 2025 in Indonesian Journal of Electrical Engineering and Computer Science
This paper discusses the process of designing and fabricating a novel compact microstrip patch Yagi-like antenna having five-patch radiating element at operating frequency 31 GHz with a bandwidth of 1 GHz. The developed design aims to optimize the antenna performance. The overall dimension of the antenna being 17× 14 × 0.8 mm3, based on RT Duroid 5880 substrate having dielectric loss tangent of 0.0009 and relative permittivity 2.2. The effectiveness of the performance of proposed design was evaluated using the electromagnetic solver Ansoft high-frequency structure simulator (HFSS) and validated by the laboratory measurements on the antenna prototype. The measured results are consistent with the simulation prediction. The designed antenna achieved directional radiation and the performances with voltage standing wave ratio (VSWR) < 1.32, return loss -17 dB and gain of 6 dBi. The measured results are compared with those existing in literature. The proposed antenna design has proven very effective in terms of the intended design and parameters which make it suitable for satellite application and wireless communication.