11 May 2020 in IEEE Access
We propose a bent corrugated substrate integrated waveguide (BCSIW) structure that can be used to design a high gain leaky wave antenna (LWA). The design removes the need for a metallic via fabrication process needed for standard substrate integrated waveguides (SIW) and displays superior performance to previously reported structures. We use simulations to compare the performance of the proposed BCSIW LWA to equivalent standard SIW and corrugated SIW (CSIW) structures, as well as experimentally characterize a fabricated BCSIW LWA. Simulation results show that the BCSIW structure can help improve the impedance bandwidth of a slotted LWA by about 14.7% while still maintaining high gain (about 13.2-17.4 dBi) as compared to an LWA based on a CSIW structure. Measurement results indicate that the proposed BCSIW LWA has a wide impedance bandwidth (32.6%) and a high peak gain (12-16.2 dBi) throughout a large frequency range from 22 to 29.2 GHz with a large beam angle range from –69° to –10°.
4 November 2019 in IEEE Access
This paper reports on a tunable bandstop filter (BSF) with both flexible center frequency and bandwidth. The tunable BSF is based on half-mode substrate integrated waveguide (HMSIW), of which the broadside is coupled with reconfigurable resonators. Using liquid crystal (LC) material as the substrate, a tunable stopband could be obtained by adjusting the bias voltage of the interdigitated microstrip resonator on LC. In order to increase the tunable range of stopband bandwidth, two additional open resonators are implemented at the broadside of HMSIW cavity. For practical validation, the bandstop HMSIW filter using LC is designed and fabricated. Numerical results demonstrate that,by adjusting the voltages of three resonators on LC, either the lower or the higher cutoff frequency could be controlled independently, leading to the flexible and independent tuning ranges of both center frequency from 4.9 to 5.4 GHz and 3-dB bandwidth of stopband from 1.2 to 1.8 GHz (@5.1 GHz).
2 September 2020 in IEEE Access
A new type of broadband circularly polarized leaky-wave antenna (LWA) with high-gain based on a corrugated substrate integrated waveguide (CSIW) structure is proposed and investigated. The CSIW structure that employs open-circuit stubs to replace metallic vias has the advantages of low-cost and easy fabrication as compared to conventional substrate integrated waveguides. Each unit-cell of the proposed LWA consists of two quarter-wavelength microstrip lines and a half-mode CSIW cell with three open-circuit stubs. Two M-shaped slots etched on the half-mode CSIW cell enables the generation of circularly polarized (CP) radiation. The full LWA, which consists of thirteen matched unit-cells cascaded along the direction of propagation enables continuous backward to forward beam scanning. The properties of the CSIW structure, including impedance matching and phase constant, are analyzed by Bloch impedance and dispersion simulations and the influence of the dimensions of the open-circuit stubs on the CP LWA performance is also investigated. A protype of the proposed LWA is fabricated and characterized. The measured results indicate that the proposed CSIW LWA has a high peak gain (9.3-12.5 dBi) throughout a large beam-scanning angle range from −28° to +25°, and the impedance bandwidth and 3-dB axial ratio (AR) bandwidth are over 40% covering the full Ka-band.
6 March 2023 in IEEE Access
In this paper, we proposed a broadband circularly polarized antenna with wide beamwidth. The main structure of the proposed antenna is a combined cross-polarized dipole antenna with four metal arms feeding by a single coaxial cable and two 90° phase delay lines. In order to attain a wide beamwidth antenna performance that can be used in a warehouse environment, we innovatively bent the metal arms and added a metal plane at a specific location to gain maximum beamwidth and the highest achievable gain. Especially, the application of folded metal arms not only reduce the space size of antenna, but also possess good axial ratio characteristic. The measurement illustrates that the antenna prototype achieves S 11 < -10 dB impedance bandwidth (IBW) of 40% (820 - 1230 MHz), a 3-dB axial ratio bandwidth (ARBW) of 7.3% (895 - 970 MHz), and a maximum half-power beamwidth (HPBW) of 104° (@915 MHz). In addition, the good radiation characteristics of a gain of 6.33 dBic and an average radiation efficiency of 76.3% were measured in the operating bandwidth, in which make the antenna a good candidate for the hasty logistics radio frequency identification (RFID) system.
3 November 2020 in IEEE Access
A leaky-wave antenna (LWA) based on the double-layer substrate integrated waveguide (SIW) that has a wide scanning range within a narrow bandwidth is proposed. The LWA consists of two layers, each of which consists of multiple elemental SIWs arranged in parallel at each layer while the direction of the SIWs in the two layers are at an oblique angle to each other. The elemental top layer SIWs are connected to those in the bottom layer though parallelogram-shaped slots, so that the two layers together form a double-layer SIW. Thin slots etched on the upper surface of each elemental SIW of the top layer act as radiating structures. As the phase difference between the radiating slots of adjacent elemental SIWs can be enlarged by the waveguide length, wide-angle beam scanning is achieved within a specific frequency bandwidth. The proposed LWA has a scanning range from −58° to 49° in a relative bandwidth of 6.45%, from 12.75 GHz to 13.6 GHz. The scanning rate (SR), defined as the scanning range divided by the relative bandwidth, is up to 16.5. The size of structure is compact, which is $4.0\lambda _{0}\times 3.6\lambda _{0} \times 0.04\,\,\lambda _{0}$ . The proposed LWA is suitable for radar or communication system applications.
10 July 2024 in IEEE Access
A slow-wave half-mode substrate integrated waveguide with a spoof surface plasmon polariton (SW-HMSIW-SSPP) transmission line structure is proposed, analyzed, and demonstrated. Results show longitudinal and lateral size reductions of more than 80% and 7 3 %, respectively, as compared with an equivalent SIW at the same cutoff frequency while maintaining a low attenuation constant of 0.02 dB/mm. By altering the geometric parameters of the SW-HMSIW-SSPP the dispersion curve can be tailored. The dispersion and electromagnetic (EM) field distribution characteristics of the proposed SW-HMSIW-SSPP unit cell and overall structure are analyzed by HFSS simulations and an equivalent circuit, and pertinent performance parameters are compared to those of SW-HMSIW and HMSIW-SSPP structures. A proof-of-concept PCB SW-HMSIW-SSPP sample was fabricated, and measurement results showing a band-pass of 4.8-11.5 GHz are found consistent with simulation results. The SW-HMSIW-SSPP structure has applications in the design of miniaturized microwave circuits.