16 January 2025 in IEEE Transactions on Transportation Electrification
It is important to predict the temperature distribution in the windings of electric machines, where the thermal model of an equivalent homogeneous material is used to simulate the winding conductors as well as the insulation and impregnation between the conductors. This article presents an analytical method for better estimating the equivalent thermal conductivity of the windings. According to the periodicity and symmetry of the heat flux field in the windings, the windings are segmented into square units, while the equivalent thermal conductivity of the whole windings is replaced with those of square units. Conformal mapping and equivalent transformation are used to reduce the complexity of solving the equivalent thermal conductivity of each square unit. Comparative study shows that the proposed analytical model is more accurate than the commonly used models. The partial stator temperature simulation was done to further verify that the proposed analytical model can be well applied to the actual windings. Experiments were conducted by fabricating and testing various winding samples, and a comparison between the finite volume method (FVM) thermal simulation and experimental tests verifies the accuracy of the proposed model.
12 September 2025 in IEEE Transactions on Energy Conversion
In interior permanent magnet synchronous machines (IPMSMs), accurately predicting the armature currents under PWM voltage supply is challenging, particularly for the harmonic components, due to a number of issues including magnetic saturation, spatial harmonics, cross coupling, and magnet eddy current reaction. In this paper, an improved time-domain model of the IPMSM with rotor virtual short-circuit windings is proposed to incorporate all these relevant effects, especially the magnet eddy current reaction effect and cross coupling in both stator windings and rotor virtual windings. The parameters of the rotor virtual windings can be identified through a standstill time-domain response (SSTR) test using the finite element (FE) method. FE simulation results and experiments of a 2.4 kW, 12 krpm 9-slot 6-pole IPMSM confirm that the proposed time-domain model has rather high accuracy in armature current prediction. The simulations of electromagnetic performance and temperature field further demonstrate that the more accurate prediction of armature currents provided by the proposed model result in a more accurate evaluation of electromagnetic performance and temperature rise for the IPMSM.
24 June 2025 in IEEE Transactions on Magnetics
A semi-analytical method is proposed for rapidly calculating the eddy current loss in permanent magnets (PMs) of interior permanent magnet synchronous machines (IPMSMs), incorporating the effects of current harmonics and PM segmentation. The eddy current reaction field is solved with the equivalent magnetic circuit model extracted from finite element (FE) analysis. The internal and external equivalent magnetic circuits of the PM are established respectively, with their parameters determined with FE sweeping and interpolation. The novelty of this work lies in fully considering the eddy current reaction effects, especially the interactions between the eddy current reaction fields in different PMs. The accuracy of the proposed method is validated through FE simulations of a 9-slot 6-pole IPMSM, demonstrating higher computational efficiency than the conventional FE method and higher accuracy than the existing semi-analytical methods. Furthermore, the proposed method is applicable to various winding and rotor configurations.
30 June 2025 in IEEE Transactions on Transportation Electrification
In electrical machines, the end winding usually has high temperature and a complex structure. Therefore, it is very important to establish an accurate thermal model of the end winding. Through simulation, it is found that the commonly used homogenization winding model is not sufficiently accurate for the end winding. This article presents a layered thermal model for both end winding and slot winding of electric machines, which are equipped with concentrated windings. According to the winding parameters such as the wire diameter and the fill factor, the layer number and the layer thickness of the layered model are calculated with a proposed analytical method. In addition, the calculation of the thermal conductivity of the insulation layer is introduced for the analytical method. Steady-state temperature field simulations using the actual winding geometric model and its layered model were carried out, respectively, and the simulation results are compared to verify the accuracy of the proposed layered model. Comparison with existing layered models and sensitivity analysis across typical machine design parameters further verify the superiority and robustness of the proposed layered model. Three winding samples with different wire diameters and fill factor are fabricated to measure the steady-state and transient temperature. The results are in agreement with the calculated results of the layered model, which further verifies the reliability of the proposed layered model.