Vadym Orel

Vadym Orel

Auto-generated profile, based on publicly available information

Vadym Orel

Zhytomyr Polytechnic State University

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 February 2016 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
ВОВадим Николаевич Орел
Вадим Николаевич Орел
ВЩВиктор Терентиевич Щетинин
Виктор Терентиевич Щетинин
АСАлександр Федорович Саленко
Александр Федорович Саленко
НЯНиколай Николаевич Яцина
Николай Николаевич Яцина
The study focuses on the possibilities of increasing the production efficiency of waterjet cutting with the aid of mechatronic systems. We have proved the effect of different types of loads and the form of the cut on the cracks in sheet workpieces. A computer simulation of a workpiece load facilitated identifying stress zones along the cutting contours. It is proved that controlling a non-stationary stress state allows limiting the crack growth rate. Increased energy efficiency and performance parameters in a complex-contour cutting of workpieces with an abrasive fluid jet is an important task for operating hydroabrasive technological complexes manufactured in a wide range by foreign and domestic firms. It is found that the most effective cutting is that with pre-loading of sheet blanks with a tensile strength up to 90 MPa. If the sheet thickness exceeds 5-6 mm the effect decreases, whereas materials thicker than 15 mm are processed with additional energy consumption. Thus, it can be assumed that when preloading devices control the stress-strain state (SSS) of the cutting area in quasi-elastic sheet workpieces the processing performance increases and the quality of the cut improves.

22 December 2023 in Mechanics and Advanced Technologies
Verified
Journal Article
Open access
OSOleksandr Salenko
Oleksandr Salenko
YDYuriy Danylchenko
Yuriy Danylchenko
VCViktor Cherniak
Viktor Cherniak
VOVadym Orel
Vadym Orel
VDValentyna Datsenko
Valentyna Datsenko
KKKostiantyn Karpenko
Kostiantyn Karpenko
The types of injuries and types of striking elements were analyzed, the conditions of patients requiring urgent surgical intervention were assessed. The possibilities of existing means of diagnosing fragments in the patient's body were analyzed, and it was concluded that for non-X-ray contrast fragments, the proposed method of mechanical contact with a special flexible and elastic probe is appropriate and effective.A special tool for examining wound canals has been developed, consisting of a flexible probe for individual use and a handle-holder with a microphone capsule, the membrane of which is directly connected to the probe and reacts to mechanical contact with an obstacle, and the capsule itself is directly connected to the oscilloscope through a signal amplifier . which has spectral signal processing circuits.The problem of the interaction of the elastic contact of a non-rigid element with a fragment located in a viscous medium is set, provided that the properties of the medium are not constant. Typical solutions of this problem for various types of fragments and parameters of the contacting element itself are presented. A picture of the noise emission accompanying the contact is shown.The functional dependence of noise emission parameters on the shape and type of the foreign object in the wound canal was revealed. The expediency of using the frequency-amplitude characteristic of noise radiation as a controlled parameter has been proven. A conclusion was made about the functional conditioning of the width of the signal spectrum and basic frequencies at the time of mechanical contact with a foreign object in the wound, depending on its shape and type; it was established that the use of an oscilloscope with a spectral analysis channel allows for the fairly accurate identification of a non-radiocontrast foreign object in a wound.

17 July 2024 in Технічна інженерія
Verified
Journal Article
Open access
PDF file
ВОВадим Миколайович Орел
Вадим Миколайович Орел
ОСОлександр Федорович Саленко
Олександр Федорович Саленко
ПМПетро Петрович Мельничук
Петро Петрович Мельничук
У сучасному аерокосмічному виробництві адитивні технології набули великого значення через їх потенціал для швидкого та ефективного виготовлення складних конструкційних елементів. Ця стаття присвячена дослідженню та аналізу різних аспектів використання адитивних технологій у створенні літальних та космічних апаратів. Зокрема, розглянуто різні методи адитивного виробництва, враховуючи топологічну оптимізацію конструкційних елементів, використання композитних матеріалів та дослідження процесів формування шарів. Особлива увага приділяється аналізу рентабельності та ефективності виробництва, а також розробці нових матеріалів для адитивного виробництва. Загальний обзор та інтеграція адитивних технологій у виробничі процеси сприяють подальшому розвитку цієї сфери та впровадженню інноваційних рішень у виробництво літальних і космічних апаратів.

26 June 2025 in Технічна інженерія
Verified
Journal Article
Open access
PDF file
ВОВадим Миколайович Орел
Вадим Миколайович Орел
ТКТетяна Федорівна Козловська
Тетяна Федорівна Козловська
ОСОлександр Федорович Саленко
Олександр Федорович Саленко
ПМПетро Петрович Мельничук
Петро Петрович Мельничук
У статті досліджено вплив механічного постоброблення на геометричні та фізико-механічні характеристики виробів, виготовлених за допомогою адитивного пошарового моделювання (зокрема, FDM). Розглянуто механізми формування дефектного шару, що виникає внаслідок порожнистої, анізотропної структури матеріалу, а також температурних і силових навантажень. Для випадку моделювання створеної адитивними процесами заготовки необхідне врахування порожнистості тіла заготовки, а також її шаруватість та компонентність. На основі чисельного моделювання визначено напружено-деформований стан заготовки під час різання, особливості розподілу деформацій та напружень між волокнами та шарами. Досліджено вплив геометрії різального інструменту, режимів різання та особливостей структури PLA-матеріалу на якість обробленої поверхні. Проведено експериментальні випробування різних способів постоброблення: точіння, фрезерування, свердління, шліфування. Отримані результати підтверджують необхідність обмеження зусиль різання та використання гострозаточених інструментів. Запропоновано практичні рекомендації щодо оптимізації постобробки виробів FDM-друку. Зазначено перспективи подальших досліджень, зокрема в напрямі врахування реологічних властивостей матеріалів.

20 October 2022
Verified
Conference Paper
Closed access
OSOleksandr Salenko
Oleksandr Salenko
Mykhaylo ZagirnyakMykhaylo Zagirnyak
Mykhaylo Zagirnyak
VOVadym Orel
Vadym Orel
SSSergii Shlyk
Sergii Shlyk
Viktoriia KulynychViktoriia Kulynych
Viktoriia Kulynych
Issues of increasing the FDM products strength due to the oscillations field imposition to the extrusion zone at the time of laying out the plastic are considered, which makes it possible to densify the laying out, increase the strips plane of the adhesive interthread and interlayer contact, and precede the extrusion of plastic beyond the laying out zone. Process simulation was performed in order to determine the rational processing modes and to establish the corresponding oscillations amplitudes and frequencies. The phenomena of plastic melt and extrusion, the temperature fields distribution on the surface of the contact strips formation, the drive dynamics during the movements algorithmic development in unsteady oscillatory motion by feed drives are taken into account. Experimental tests the proposed algorithmic solutions were carried out, a number of product demonstrators were made in the test cube form (20x20x20 mm) and a blade for tensile testing (160 mm). It is shown that due to the oscillations imposition at the extrusion zone, it is possible to increase the tensile strength of products by 15-18%, and a greater increase is observed in the plane of the work table. The possibility of achieving strength parameters approximately corresponding to the filament strength is shown. Further research with reinforced plastics and PEEK group plastics is recommended.

27 June 2025 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
OSOleksandr Salenko
Oleksandr Salenko
VSVasil Strutinsky
Vasil Strutinsky
KAKonstantyn Avramov
Konstantyn Avramov
VOVadym Orel
Vadym Orel
DDDmytro Dzhulii
Dmytro Dzhulii
AKAnton Kostenko
Anton Kostenko
The object of this study is the FDM process underlying the 3D printing of thin-walled honeycomb-type shells. A solution to the problem of manufacturing a honeycomb filler for a sandwich panel or a panel as a whole, including a curved one, is based on the built model of the process parametric and functional reliability. To this end, the printer dynamics, the behavior of a non-rigid workpiece, and the peculiarities of filament feeding during printing have been analyzed in detail. It has been shown that the predicted mechanical properties, in particular, [σ]x,y,z, are determined by the conditions of extrudate laying and the adhesive bonds formed between its elements, both in the laying plane and between layers, and depend directly on the laying density and on a number of dynamic and thermal phenomena occurring in the mating area. The layout density parameter ρ can be used as a factor in the strength characteristics of the finished article. The application of rational conditions for the movement of the print head, certain features of the contour traversal, the use of supporting elements, and the correct positioning of the part on the printer’s desktop allows for sufficiently reliable reproduction of cellular shell products with maximum strength. It has been proven that the accuracy of basic dimensions of the designed structures corresponds to accuracy quality 11...12 according to engineering standards, which is acceptable for a wide range of applications. The wall thickness of the cellular elements is determined by the filament laying modes, which includes such parameters as extrusion speed, contour traversal speed and acceleration, extrusion temperature, and stacking pitch, but is not less than 1.5 times the diameter of the extruder nozzle. Such geometric parameters provide reasonable strength and rigidity for articles at operation while minimizing the weight of the honeycomb. It has been established that cellular elements should be printed with the use of additional support means; at the same time, the latter do not exclude the occurrence of a certain number of defects whose evolution is not stable and whose presence must be taken into account when predicting the mechanical properties of the finished article