1 October 2018 in Journal of Composites for Construction
This paper presents an experimental study on the bond durability of basalt fiber–reinforced polymer (BFRP) bars, steel–fiber reinforced polymer (FRP) composite bars (SFCB), and steel bars embedded in seawater sea-sand concrete (SWSSC) and subject to a simulated ocean environment. The effects of the environment type, exposure period (i.e., 3, 6, and 9 months), and reinforcement type on bond durability were investigated. The degradation mechanism was analyzed using scanning electron microscopy (SEM). The test results showed that after being conditioned, the failure mode changed from shear failure at the BFRP rib-concrete occlusal interface to the peeling of the BFRP surface. For the BFRP bars, after 9 months of aging, the bond stress retention was 92% in the wet-dry cycling environment and 78% in the immersion environment. For the SFCBs, after 9 months of aging, the retention in the wet-dry cycling environment was 100% and that in the immersion environment was 90%. For the steel bars, although there was no reduction in bond strength, pitting corrosion was observed at the bar surface. The predicted bond stress retention of BFRP bars embedded in SWSSC after 50 years of service life in various environmental conditions ranged from 47% to 83%.
1 September 2016 in Journal of Structural Engineering
The implementation of reliability methods for designing new structures and assessing the safety and evaluating the performance of existing structures and infrastructure systems has gained widespread acceptance. Consequently, reliability-based design specifications in the form of load and resistance factor design (LRFD) methods have dominated the development of current codes and standards. This paper reviews the reliability-based performance criteria used to calibrate design and evaluation codes and standards for assessing the strength, serviceability, and fatigue resistance of structural components. The review shows that large differences exist in the target reliability levels adopted for evaluating the strength of various types of structural members and materials. These differences result from many factors, including (1) intended structure design and service life; (2) expected member modes of failure (e.g., ductile or brittle); (3) importance of the individual member to overall system integrity (...
1 October 2012 in Advances in Structural Engineering
Carbon fibre reinforced polymer ( CFRP) has shown promise for improving the fatigue performance of steel structures. Previous studies have indicated that increasing the Young's modulus of CFRP can be beneficial for decreasing the stress intensity factor at the fatigue crack tip. In this project, ultra high modulus (UHM) CFRP plates with Young's modulus of 460 GPa were adopted to study their fatigue repair effectiveness. A series of fatigue tension tests was carried out on steel plates with an initial crack in the centre. Five strengthening configurations were used and a constant amplitude fatigue loading was applied to all the specimens. The beach marking technique was utilized to record the fatigue crack propagation. The effects of CFRP bond length, bond width and bond locations on the fatigue performance of cracked steel plates were also studied. The experimental results show that UHM CFRP plates can greatly increase the fatigue life of cracked steel plates by a factor ranging from 3.26 to 7.47. When CFRP plates cover the whole crack surface, the fatigue crack of the steel plate is arrested. The strengthening effectiveness of UHM CFRP plates is also compared with those using high Young's modulus CFRP sheeting and normal Young's modulus CFRP plates with or without prestressing.
1 June 2014 in Journal of Composites for Construction
Carbon fiber reinforced polymer (CFRP) has great potential in strengthening steel structures and the bond between CFRP and steel is a critical issue in the strengthening technique. State-of-the-art reviews have been reported in the literature on the bond behavior between CFRP and steel under static loading at ambient temperature. However, steel structures are often subjected to dynamic loading and harsh environment conditions, and the bond between CFRP and steel may be affected by these conditions. This paper presents a state-of-the-art review on the effects of dynamic loading (e.g., fatigue, impact, and earthquake) and environmental conditions (e.g., subzero temperatures, elevated temperatures, sea water, and ultraviolet light) on the bond between CFRP and steel. The combined effect of applied loading and environmental conditions is also included. Directions for future research are indicated and a comprehensive reference list is provided.
11 May 2013 in Fatigue & Fracture of Engineering Materials & Structures
1 October 2017 in Journal of Composites for Construction
Hollow structural members are highly vulnerable structural components subjected to transverse impact loads. These tubular members have been used widely in both onshore and offshore structures where lateral impact forces can be expected from moving vehicles/vessels or terrorist attacks. Thus, strengthening of steel hollow tubular members is required to safely carry both service static and imposed dynamic impact loads. This paper presents the results from a series of tests on bare and fiber-reinforced polymer (FRP) strengthened circular hollow-section (CHS) steel members subjected to transverse impact loading at midspan. A total of 14 (2 bare and 12 strengthened) medium-scale specimens were tested to investigate the effect of FRP wrapping on the global and local deformation capacities of strengthened members under drop-hammer impact. Both carbon-fiber-reinforced polymer (CFRP) and glass-fiber-reinforced polymer (GFRP) sheets were used as strengthening materials. The results indicate that the FRP strengthening of the tubes enhances their impact-resistance capacity by reducing lateral displacements up to 29% compared to bare steel CHS specimens. The influence of FRP type, CFRP orientation, CFRP thickness, and effective bond length on the structural response and failure behavior of wrapped members were investigated. The results showed that the application of FRP in the longitudinal direction was effective to control the global deformations whereas the hoop layers were effective in reducing local inward deformations of CHS members.