Leong Wen Chek

Leong Wen Chek

Auto-generated profile, based on publicly available information

Leong Wen Chek

Power Electronics and Renewable Energy Research Laboratory, Department of Electrical Engineering, Faculty of Engineering, Universiti Malaya, Kuala Lumpur, Malaysia

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 September 2018 in Energies
Verified
Journal Article
Open access
PDF file
WTwajahat Tareen
wajahat Tareen
ZAZuha Anjum
Zuha Anjum
NYNabila Yasin
Nabila Yasin
LSLeenah Siddiqui
Leenah Siddiqui
IFIfzana Farhat
Ifzana Farhat
LCLeong Wen Chek
Leong Wen Chek
Pakistan is experiencing an undersupply of electricity, causing load shedding several hours per day due to the adherence to conventional energy resources having quantitative and environmental limitations. Fossil fuels generate more than half of the country’s total electricity, but they will ultimately run out due to their limited supply. Their combustion emits greenhouse gases, posing environmental threats. Since the world is tending toward efficient and sustainable alternative methods for harvesting energy from nature, Pakistan has also been investigating an elevated deployment of renewable energy projects. This paper presents a critical analysis of the present energy sector of Pakistan along with global scenarios. Pakistan relies on mainly thermal, hydro, and nuclear energy for power generation. National solar, wind, geothermal, and biomass resources have not been extensively explored and implemented. This paper provides an insight into the potential of these resources in Pakistan to generate electricity for the national grid on a large scale. It focuses on biomass energy, which can be harnessed from bagasse, poultry waste, and municipal waste for power production, and biomass-based fuel for industries and transportation. It concludes that biomass is the most sustainable, available, implementable, and environment-friendly resource that can be utilized to lessen the energy demand and supply gap in Pakistan.

8 April 2022 in IEEE Transactions on Industry Applications
Verified
Journal Article
Closed access
LCLeong Wen Chek
Leong Wen Chek
Saad MekhilefSaad Mekhilef
Saad Mekhilef
HRHarikrishnan Ramiah
Harikrishnan Ramiah
A magnetron is one of the most common microwave power generators used in commercial or industrial applications. There are a few methods for optimizing the magnetron to enhance its efficiency, which include the selection of the building materials, increasing the resonant cavity, enlarging operation space size, and modifying the anode structure. This article proposes the modification of magnetron cathode for high-frequency and low-power applications using gallium nitride (GaN)-coated cathode replacing the current barium oxide (BaO) coat. The highlighted optimization is intended to modify the control of magnetron electron drift velocity, heat dissipation, operation frequency, and power generation. Simulation and experimental results have been extracted at 2.45 GHz to generate 5 W microwave power and tested for over 30 ft. of power transmission using a rectenna interface, which results in an efficiency of 88.37%, compared with 51.8% using BaO coat.

8 April 2021 in International Journal of Microwave and Wireless Technologies
Verified
Journal Article
Closed access
PDF file
LCLeong Wen Chek
Leong Wen Chek
Saad MekhilefSaad Mekhilef
Saad Mekhilef
HRHarikrishnan Ramiah
Harikrishnan Ramiah
Semiconductor deposition on magnetron's cathode surface using different materials such as gallium nitride (GaN) and silicon carbide (SiC) semiconductors is conducted to grow approximately 80, 100 and 120 nm plasma layers. The cathode is then used to generate high frequency and low-power microwave for further comparison and analysis with the conventional magnetron operation. Parameter of analysis to identify the efficiency includes electron drift velocity, harmonic order, total harmonic distortion, low harmonic distortion, and spectrum observation. The sputtered cathode of the magnetron is used to generate a low-power microwave observing a generator efficiency up to 93 and 88% for GaN and SiC materials, respectively, compared to the conventional material, which observes 37% of efficiency at 2450 MHz, 5 W. Also reported is the quality of semiconductor sputtering on the magnetron cathode, which was manipulated by the deposition period, temperature, and plasma layer growth thickness.