Muhd Ridzuan Mansor

Muhd Ridzuan Mansor

Auto-generated profile, based on publicly available information

Muhd Ridzuan Mansor

Universiti Teknikal Malaysia Melaka (UTeM)

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 May 2015 in Applied Mechanics and Materials
Verified
Journal Article
Closed access
PDF file
MMMuhd Ridzuan Mansor
Muhd Ridzuan Mansor
SSS.M. Sapuan
S.M. Sapuan
AAArep Ariff
Arep Ariff
EZEdi Syam Zainudin
Edi Syam Zainudin
ANA.A. Nuraini
A.A. Nuraini
Spoilers are part of an automotive exterior bodywork system that acts to create additional down force for higher traction. In this paper, a new conceptual design of automotive spoiler component using kenaf polymer composites was developed using integrated TRIZ and morphology chart design method. The aim is to enable direct application of kenaf polymer composites to the spoiler design to achieve better environmental performance of the component while maintaining the required structural strength for safe and functional operation. The overall process involved two major stages, which are the idea generation and concept development. TRIZ method was applied in the idea generation stage where specific solution strategies for the design were created. In the concept development stage, the specific TRIZ solution strategies obtained were later refined into relevant alternative system elements using Morphology chart method. Finally, a new conceptual design of an automotive spoiler was developed using the combination of the identified system elements. The integrated TRIZ and morphology chart method were found to be new tools that can be used effectively in the concept design stage, especially in cases where direct material substitution is given the main focus for the new product development.

1 January 2020
Verified
Book Chapter
Closed access
MMMuhd Ridzuan. Mansor
Muhd Ridzuan. Mansor
MAMohd Zaid. Akop
Mohd Zaid. Akop

19 March 2023 in Journal of Electrochemical Science and Engineering
Verified
Journal Article
Open access
PDF file
BBBasori Basori
Basori Basori
WMWan M. F. W. Mohamad
Wan M. F. W. Mohamad
MMMuhd R. Mansor
Muhd R. Mansor
NTNoreffendy Tamaldin
Noreffendy Tamaldin
Agung IswadiAgung Iswadi
Agung Iswadi
FSFerry Budhi Susetyo
Ferry Budhi Susetyo
Hydrogen production could be enhanced by increasing the potassium hydroxide (KOH) concentration, but higher KOH concentrations result in higher corrosion rates. Therefore, a deep investigation of the electrochemical behavior of stainless steel (SS 316L) in the KOH solution is needed. This study investigates the influence of KOH concentrations on the electrochemical behavior, surface morphology, structure, and sample phases of SS 316L. The investigations were conducted by some electrochemical techniques, UV-vis, scanning electron microscopy-energy dispersive spectroscopy (SEM-EDS), and X-ray diffraction (XRD). The corrosion rate was found to increase, and solution resistance to decrease with increasing KOH concentration. Samples tested in 5, 30, and 50 g l-1 of KOH showed corrosion rates of 0.457, 2.362, and 5.613 µm year-1, respectively. A wide passive region and the noblest pitting potential were noticed for the sample with 5 g l-1 of KOH. Moreover, Mott-Schottky plots and characteristic wavelengths of UV-Vis suggest the formation of iron and chromium oxides by the passivation of samples. The SEM analysis showed a dynamic change of surface morphology from the lowest to the highest concentration with the intergranular corrosion found at the grain boundaries area. In conclusion, concentrations < 50 g l-1 KOH could be recommended since they would support the optimum remaining life of SS 316 L plates in HHO generators.

1 January 2025 in International Journal of Lightweight Materials and Manufacture
Verified
Journal Article
Open access
RYRu Vern Yiow
Ru Vern Yiow
MMMuhd Ridzuan Mansor
Muhd Ridzuan Mansor
MSMohd Adrinata Shaharuzaman
Mohd Adrinata Shaharuzaman

6 June 2014 in Applied Mechanics and Materials
Verified
Journal Article
Closed access
PDF file
MMMuhd Ridzuan Mansor
Muhd Ridzuan Mansor
Mohd Sapuan SalitMohd Sapuan Salit
Mohd Sapuan Salit
EZEDI SYAMS ZAINUDIN
EDI SYAMS ZAINUDIN
Nuraini Abdul AzizNuraini Abdul Aziz
Nuraini Abdul Aziz
AAArep Ariff
Arep Ariff
Multi criteria decision making (MDCM) methods are amongst the approaches available in aiding composite designers to make the final decision especially during the material selection process where multiple solutions are present and various requirements are required to be satisfied simultaneously. Thus, in this paper, material selection process of thermoplastic matrix using MDCM methods for hybrid natural fiber/glass fiber polymer composites is presented. The aim is to identify the most suitable type of thermoplastic matrix to be used in the hybrid polymer composites formulation. The Weighted Sum Method (WSM) is applied in the selection process of seven candidate thermoplastic matrix materials based on the product design specifications. The overall analysis highlights that low density polyethylene (LDPE) is the preferred matrix for the intended application based on the highest scores obtained compared to other candidate materials. A signal-to-noise (S/N) ratio analysis was further performed to validate the initial selection results where LDPE once again outperformed other candidate materials with highest S/N ratio score in the non-compensatory approach.

14 June 2018
Verified
Book Chapter
Closed access
PDF file
MMM.R. Mansor
M.R. Mansor
Mohd Sapuan SalitMohd Sapuan Salit
Mohd Sapuan Salit
This chapter presents the case study of the concurrent design methods in solving the design barrier created by the inherent mechanical properties of kenaf composite materials toward improving product performance. Decision-making in kenaf composite material selection involves two stages, namely the screening stage and ranking stage. The analytic hierarchy process method was applied in the decision-making process and the final results showed that kenaf fibers are the most suitable candidate material to form the hybrid composites for automotive parking brake lever components. Natural fiber composites (NFC) product development is especially related to kenaf composites, and the product requires the simultaneous consideration of different aspects which are materials, design, and manufacturing in the early stage of the design process. The implementation of the concurrent design method in NFC product development can contribute in shorter design cycle and reducing the product design time. Kenaf composites have a lower density compared to steel, and are therefore able to produce lighter shelf bracket components.