1 September 2021 in Aerospace Science and Technology
1 May 2022 in AIP Advances
The aerospace vehicle flying at hypersonic speed, using an airbreathing propulsion system based on supersonic combustion (scramjet) technology, requires a highly integrated system without moving parts, making the propulsion system and vehicle shape indistinguishable. A scramjet uses shock waves, generated by its inlet during the hypersonic flight to provide the temperature and velocity of atmospheric air to burn the hydrogen, at the combustor at supersonic speed. The divergent exhaust nozzle accelerates the combustion products providing the thrust. A two-dimensional hydrogen-powered generic scramjet has been designed to demonstrate supersonic combustion in atmospheric flight at a Mach number of 6.8 and an altitude of 30 km. Temperature and velocity at the combustion chamber are the most important key parameters for a preliminary design. The inlet configuration must provide a temperature higher than the ignition temperature of the fuel to guarantee spontaneous combustion and the velocity must remain supersonics. The nozzle exit velocity should be higher than the vehicle flight velocity to obtain sustained flight and produce enough thrust. For this theoretical analysis, the air is considered a calorically perfect gas without viscous effects. The compressible flow is analyzed based on oblique shock waves and one-dimensional compressible flow with friction and heat addition and Prandtl–Meyer coupled to the area ratio to describe each key component of the scramjet, such as compression, combustor, and nozzle sections, respectively. The inlet mass flow and hydrogen mass flow are also critical for the scramjet design to ensure stoichiometrically combustion at the combustion chamber, generating the high flow velocity at the nozzle to produce thrust.
1 January 2017 in International Journal of Aerospace Engineering
IRIsrael da Silveira Rêgo
PTPaulo Gilberto de Paula Toro
Paulo Gilberto de Paula Toro
The Brazilian hypersonic scramjet aerospace vehicle 14-X B is a technological demonstrator of a hypersonic airbreathing propulsion system based on the supersonic combustion (scramjet) to be tested in flight into the Earth’s atmosphere at an altitude of 30 km and Mach number 7. The 14-X B has been designed at the Prof. Henry T. Nagamatsu Laboratory of Aerothermodynamics and Hypersonics, Institute for Advanced Studies (IEAv), Brazil. The IEAv T3 Hypersonic Shock Tunnel is a ground-test facility able to produce high Mach number and high enthalpy flows in the test section close to those encountered during the flight of the 14-X B into the Earth’s atmosphere at hypersonic flight speeds. A 1 m long stainless steel 14-X B model was experimentally investigated at T3 Hypersonic Shock Tunnel, for freestream Mach numbers ranging from 7 to 8. Static pressure measurements along the lower surface of the 14-X B, as well as high-speed Schlieren photographs taken from the 5.5° leading edge and the 14.5° deflection compression ramp, provided experimental data. Experimental data was compared to the analytical theoretical solutions and the computational fluid dynamics (CFD) simulations, showing good qualitative agreement and in consequence demonstrating the importance of these methods in the project of the 14-X B hypersonic scramjet aerospace vehicle.
27 February 2019 in International Journal of Aerospace Engineering
IRIsrael da Silveira Rego
PTPaulo Gilberto de Paula Toro
Paulo Gilberto de Paula Toro
In order to overcome the drag at hypersonic speed, hypersonic flight vehicles require a high level of integration between the airframe and the propulsion system. Propulsion system based on scramjet engine needs a close interaction between its aerodynamics and stability. Hypersonic vehicle nozzles which are responsible for generating most of the thrust generally are fused with the vehicle afterbody influencing the thrust efficiency and vehicle stability. Single expansion ramp nozzles (SERN) produce enough thrust necessary to hypersonic flight and are the subject of analysis of this work. Flow expansion within a nozzle is naturally 3D phenomena; however, the use of side walls controls the expansion approximating it to a 2D flow confined. An experimental study of nozzle performance traditionally uses the stagnation conditions and the area ratio of the diverging section of the tunnel for approaching the combustor exit conditions. In this work, a complete hypersonic vehicle based on scramjet propulsion is installed in the test section of a hypersonic shock tunnel. Therefore, the SERN inlet conditions are the real conditions from the combustor exit. The performance of a SERN is evaluated experimentally under real conditions obtained from the combustor exit. To quantify the SERN performance parameters such as thrust, axial thrust coefficient and lift are investigated and evaluated. The generated thrust was determined from both static and pitot pressure measurements considering the installation of side walls to approximate 2D flow. Measurements obtained by a rake show that the flow at the nozzle exit is not symmetric. Pitot and pressure measurements inside the combustion chamber show nonuniform flow condition as expected due to side wall compression and boundary layer. The total axial thrust for the nozzle obtained with the side wall is slightly higher than without it. Static pressure measurements at the centerline of the nozzle show that the residence time of the flow in the expansion section is short enough and the flow of the central region of the nozzle is not altered by the lateral expansion when nozzle configuration does not include side walls.
1 January 2020 in Journal of Aerospace Technology and Management
During the last decade, the world faced the mass insertion of small satellites in the space technology scenario. Every year, the number of micro and nanosatellites launched increases and gets more attention from players in the space market. Despite the lack of a national launcher, the Brazilian Space Program is known for some successful development in the last century, including its space assets, such as a privileged launch site near the equator, a family of flight proven and reliable sounding rockets for suborbital flights and microgravity experiments and universities with established small satellites programs. Thereby, the present work proposes a modification of the Brazilian VSB-30 sounding rocket in order to allow the launch and insertion in low Earth orbit (LEO) of small satellites fulfilling the gap of a national launcher. It also presents a CubeSat orbital decay simulation and orbital insertion simulation with the modified rocket launched from the Alcantara Launch Center as a matter of verifying the potential of national missions using this modified launcher.